xuav clouds 3d models

This is to support the tail on the Xuav Clouds. I used a Kite spar that's 3.5m thick and cut down too 10 inches. this will stiffen up the tail while still allowing disassembly. ...The Tail Spare is just held in with friction but you can permanently glue...

Whilst building the Xuav clouds I noticed when I tightened down the screws on the rear hatch it was pulling the entire hatch below the airframe which I didn't like, I designed this small hatch stop to stop this happening. I then found out the front...

This is a FC Mount plate for the XUAV Clouds that allows clean cabling around the FC and easy access to the SD Card as well as USB. The cables can be routed through the openings around the FC and with a bit of excess wire it allows you to lift the...

I didn't feel like the clouds looked finished with the motors exposed, so I designed these cowls to clean up the looks a bit. These were designed around a Turnigy Multistar 2814-700Kv which has an outside dimension of 35x36mm. The 35x36 size motor is...

Simple micro cam mount for XUAV clouds Compression fits the cam.

This is a collection of parts I designed to work with the XUAV-Clouds aircraft. It includes: 1. Nosecone with pan and tilt mount for a GoPro-sized action cam. Designed for GWS S125 1T 360 degree pan servo. For tilt you can use any 9 gram servo,...

When I put the GPS for the Vector in the depression made for it on the XUAV clouds, it just didn't look like it was going to stay put. So i made this holder for the GPS. The hole in the middle is for the GPS clip screw I printed in black ABS, ...

whilst using the rear hatch stop I found out that there is a requirement for spacers between the hatch and the nut that holds the rear hatch on. this keeps the rear hatch level with the rest of the airframe. will update the pictures once printed.

i had a small issue where the gps i was planning to use did not fit in the holder so i modded it to fit, part will now accept - eagletree vector gps, MFD AP gps Pitlab gps, RVOSD gps can be modded to fit others if needed

I liked the Pitot mount from BreakX, and intended to print it in TPU, however my printer was just not going to print it for me. ( tried about 10 times) I decided to change the design a little bit. I used the rubber vibration dampener balls that I...

A simple GPS Bay cover for better airflow if a blank GPS module like Matek M8Q, Beitian BN-880 or other modules without housing are used. ... Print with support to have a clean surface finish and use a few drips of solvable glue to fix in place.

I'm using a pair of T-Motor MN3110, so the bolt pattern is for that series of motors.

I was finding that the bolts that hold down the hatches were slowly pulling into the foam so made caps to sit in the foam that stopped this happening. ... quick and easy fix

X-UAV Clouds rear facing pop-up camera mount Parts used: Camera - Foxeer Falkor Micro Servo - Emax ES9251 Hinge Pin - 23mm section of round 3mm carbon rod Bolts - 2x 12mm M3 Servo control rod - 2mm steel rod with z-bends in each end. Length to suit.

Just a simple part to glue in and make it so you can Velcro in a camera such as Runcam2, Session, etc.

I made this quickly just to adapt the T-motor 4006 740kv motors to the XUAV Clouds, and later the Mini/Snow Goose.

copy of XUAV Drone

This fit perfectly on latest Skysurfer from XUAV which lately sells on shops like Banggood. I removed the bridge part from the original in order to reduce weight. Also there is a hole to route cables from inside the fuselage, but also some holes to...

clouds

A lowpoly cloud.

a cloud box

I love clouds....

Cloud-shaped cookie cutters, three sizes!

clouds nut holder need to be scaled larger

After printed two Balloon Lampshade, and attacked on the ceiling, I wanted some 2D clouds. More shapes are coming. ... The Balloon Lampshade -> https://www.thingiverse.com/thing:511417

This is a Wing-Lock for the XUAV Talon. I didn't like the fact that the wings are just hold on by friction. So I made a Wing-Lock to stop them from falling off in mid-flight. ...Here is a little tutorial on how to install them.

This object was made in Tinkercad. ...Edit it online https://www.tinkercad.com/things/cYMZOKGiE0b

No description provided.

See in my library my proposition :Clouds trees. ...I don't know why my entries disappear in this challenge. Maybe when i rewrite over my text ? PLEASE SEE: Clouds trees ALSO: UMBRELLA CLOUD AND

auspicious clouds ,to decorate your room ,you can scale it into different  size before you print it ,so you will get more beautiful clouds