y clamp 3d models
171636 3d models found related to y clamp.
thingiverse
The original Y clamp always broke and get loose around the shaft. ... I designed this split version to try make it more robust and have a tighter fit on the shaft.
thingiverse
I took the clamp that attached the bed to the t-belt as a template and modified it to have an arm that sticks out and can hit the y-stop switch. ...Based on http://www.thingiverse.com/thing:30394 ...
thingiverse
... was made 20mm longer than the Mendel version to accommodate any modifications to the y-table. ... This model is for a 8mm bar. Instructions I basically designed from scratch based upon NOPHEAD's Mendel 90 Sturdy STL for the Y-Bar Clamp for 10mm bar
thingiverse
as in title Y belt clamp, simply slide your belt in and clamp it to the bed bracket, you will need a bit longer bolts tho
thingiverse
... right side as seen from the front. On the y carriage I threaded the left side of the lm8uu clamp using an M4 tap. ... Redesigned the clamp to take an countersunk M4x8 screw from the bottom side and thinned it so that it clears the stepper motor.
thingiverse
A custom y shaft clamp so I can apply plexiglass on the outside of the Hypercube so it becomes an enclosure.
prusaprinters
I've mounted a 60mm high torque NEMA17 motor on my P3Steel y axis. However the toolson designed lm8uu clamp hit the back of the motor, which is mounted on the right side as seen from the front. On the y carriage I threaded the left side of the lm8uu...
thingiverse
Because the original clamps are a little hard to print because of bridging, I designed this Y-clamp that can be printed up side down. Also made a X-clamp for the LM8UU bearing X-Carriage. This one can also be printed up side down. This thing was...
thingiverse
This part has been replaced by version 2.0: http://www.thingiverse.com/thing:3843 This is a parametric one-piece y-bar clamp. It replaces two y-bar clamp pieces from Mendel or Mini Mendel, and requires no screws! This is part of a larger project to...
thingiverse
This Y carriage clamp is inspired on "HyperCube Evolution Igus Carriage Clamp tenser" from Thingiverse user "endeffect" and the original Y carriage clamp from "SCOTT_3D". The purpose of this clamp is to take the pressure of the bearings when...
prusaprinters
Because the original clamps are a little hard to print because of bridging, I designed this Y-clamp that can be printed up side down. Also made a X-clamp for the LM8UU bearing X-Carriage. This one can also be printed up side down.</p> <p>This thing...
thingiverse
The original Y_Shaft_Clamp is a bit too fiddly for my big thumbs and so I decided for a remix. There is enough space in this place to install a larger bracket. Just insert a M3 nut from above into the slot and a M3x12 screw from the side to pinch the...
thingiverse
Instructions Get an M4x40 machine screw with washer and put it in the round end of one of the two central holes in the clamp body. Put an M4 nut on the screw and do it up very tightly. This will seat the M4 nut permanently in a wad of loose plastic...
thingiverse
Just a simple y-rod-clamp for the Prusa I3 MK3 to get rid of the ugly looking zip ties
thingiverse
Must be printed: - 2x Bottom Y Belt Clamp - 1x Top Y Belt Clamp. Both pieces have a flat side, while the other side is reccessed in order to fit the belt. I'd recommend to use a little drop of CA glue between the Top Y Belt Clamp and the...
thingiverse
The upgraded version of the Y bar clamps we use on the Ecksbot ZA derivative. Thanks to Peter from OpenHardware for the design. ... Instructions Print 4 of these and use them instead of the standard bar clamps.
thingiverse
This is the Cover for my previous posted Y-Belt Clamp. You should use this if you print the Clamp with PLA! Update!: This is the Cover for the Original Belt Clamp. ...An updated Version for the Glasfiber reinforced GT2 Belts will be coming soon!
thingiverse
Here is the Y endstop clamp I have been using. It is for a 0.5"x0.225"x0.25" body microswitch. It could be modified in sketchup for a different size switch. Instructions Print Mount to aluminum...
thingiverse
It replaces two y-bar clamp pieces from Mendel or Mini Mendel, and requires no screws! The previous version ran the risk of delaminating under stress. This version is modified to print on its side, as per Erik's suggestion, which should make it...
thingiverse
Instructions Use the groove sides to clamp chain, the smooth side to clamp belts. Use a length of woodscrew such that the belt/chain can be grabbed but the pointy bit does not protrude through the bed. ...Full bed plans and assembly details here:...
thingiverse
Clamp-on Y-axis end stop holder for the Prusa I3 printer The Y-axis end stop holder broke off of the y-motor piece on my printer and I didn't feel like disassembling the whole thing to put on a new one so I made a clamp-on version of the end stop...