y guide 3d models

What it does: Makes a bearing block somewhat floating / self-aligning and is meant to be used "only" on the guiding bearing block of the Y-axis, and only on the Y-axis (that single block in a triangle setup). Mainly to hopefully avoid/reduce...

For this Y carriage https://www.thingiverse.com/thing:3138686

RepRapPro Mendel Y Belt Guide. ...Easy installation.

Guide rod holders for the Y axis.

Print Settings Printer: Re-D-Bot Rafts: Doesn't Matter Supports: No Resolution: 0.2 mm Infill: 30% with 100% layer ever 20 layers Notes: Other parameters Perimeters: 4 Top/Bottom layers: 4 01.14.17 update Added version for LED strip New files:...

Print Settings Printer: Re-D-Bot Rafts: Doesn't Matter Supports: No Resolution: 0.2 mm Infill: 30% with 100% layer ever 20 layers Notes: Other parameters Perimeters: 4 Top/Bottom layers: 4 01.14.17 update Added version for LED strip New files:...

To connect the Linear Rail Mount to both the "updated_Y-Carriage-3-Wheels-1-Left/right" and the "Y-Carriage-3-Wheels-2_x2.stl" parts, which are still connected at the bottom the original way, I thought M3 bolts were strong enough. I made a...

This is my new carriage for Y-axis. Now i'm using MGN12 rails and MGN12H carriages, instead wheels. Also I placed them to bottom of profile - this solution much better for me. ...It's looks pretty well now ~_~ ####Where I bought rails: - 2 x [MGN12...

This is a Y Bearing guide with a thicker plate for a Printrbot. Instructions During our construction, this was the part that gave us the most concern - the flat plat was thin enough to be flexible,...

This is a Y Bearing guide with a thicker plate for a Printrbot. Instructions During our construction, this was the part that gave us the most concern - the flat plat was thin enough to be flexible, and it took quite a bit of pressure to seat the...

Ender3 duct , easy removal of hot end , better visibilty of printing

Needed a quick and dirty filament guide because I am traveling with a printer and have a spool set behind the printer. Fits a 6.5mm frame of a prusa or variant. Scad file included for editing but I did not nicely parameterize this one. ...

This guide attaches to the Y carriage and holds the harness up. NOTE - need to make this out of ABS or other high temp material because if you use PLA, it will weaken and bend as soon as you print with a hot (>60°C) bed. ...Print Settings Printer: ...

I created this Chain Guide to prevent the bed leveling sensor from catching while Auto-Leveling or while printing large objects. ...This guide keeps the cable chain below the level of the bed itself, out of the way.

This is my fix for the floating end of the Y-axis on the Makibox. ...It replaces the original spacer clamp and runs along a 1/2 x 1/2 inch L-bracket (13mm x13mm).

Matching my frame construction from AL profiles, here is the construction of the Y-axis. The cable carrier is made by a chain from IGUS. However, other chain can be selected and the holders adapted. All necessary data including BOM are in the...

Standard acessories do avoid z and y woble,. ... To hold Z and Y Guide. ... You need to print 4 of them to use in upper Z (2) and back Y (2)

... The holes for the Y-Cable Guide are already there. I used double sided tape and sheet metal screws to secure it. The guide for the hot bed is only clicked. Works well from the inside out. It is best to use zip ties to secure the cable.

Detail for upgrade from D-Bot rails update kit (https://www.thingiverse.com/thing:2170087) with 2020 on X-axis to Re-D-bot Y carriage on rails (https://www.thingiverse.com/thing:2834162).

Профиль 2020 располагается сверху. Рельса - снизу. Можно применять совместно с https://www.thingiverse.com/thing:2474187 , нужно только поменять местами верхнюю и нижнюю поперечину на каретке с экструдером. ...Или...

This is a filament guide that is easily snap on on the back of the back of the Motor Y. ... You will need a roller dia.8xdiam22x7 and one M3 screw.

The Y-Axis rod back-up plates on my Anet a8 finally broke, here is a replacement plate that can replace the plates for the Y and the Z axes. Hope you enjoy! ...Happy printing!

... to avoid gap between rod and structure. ... It will be decrease wobble in Z and Y axis. Need to be assembly in opposite of the limiter mount of each rod. Dont need new screw or other hardware to assembly, just put it in existing mounting. ...

This is a remix and update of (once i find the original i will add the details here) a set of Y axis brackets, I added a set for the outside of the case to reinforce the screw holes a bit as i managed to tighten one of the screws too much and put it...

I installed pillow blocks and calibrated my CTC but forgot to do the Y axis guides while I was there and really cant be bothered going through the misery of opening it up again! So here are Lazy Y axis guides that you can snap on without any...

Y-axis guide and tensioner for Velleman K8200 Requires: a ball bearing 13x5x5 2 slices subject 19x5x1.2 4 slices subject 10x5x1 1 M5 Allen screw 30mm long 4 M4 screw min 10mm long

Use a total of four of these to support front and rear of each of the two Y axis guide rods. The original wooden supports allow a lot of play. Use M3 cap-head stainless bolts from the original wooden mount to secure thing to printer frame. Fixing...

Sources included I bought these motors [here][1] [1]:...

Hier die weiteren Änderungen passend zu Gestell. ...Halter wurde gedruckt und mit dem Gestell zusammengebaut.