yaesu ft 60 battery 3d models
149977 3d models found related to yaesu ft 60 battery.thingiverse
Mockup of the FT-60 stock nimh battery for modification. Will change in the future to hold two 18650s. !UPDATE! ... Here is the 18650 holder completed: https://www.thingiverse.com/thing:3413951
thingiverse
My Yaesu FT-60 had a difficult to use volume knob, so I got inspired by this version: https://www.prusaprinters.org/prints/137075-yaesu-ft-60-volume-knob-v2/files And created my own.
thingiverse
Yeasu FT-60 Wall Mount PS: Form factor is perfect, radio fits in, all within specks after PLA print..
thingiverse
Battery replacement cover for the Yaesu FT-817/817ND and probably the FT-818. The published part has no callsign added. ...You can add this on Tinkercad.
thingiverse
This is a remix of very well designed Yaesu FT-4X Battery box from thazlett, https://www.thingiverse.com/thing:4446212 i just add some tollerance and beef it up to be less flexible. Also i lowered the contacts sims to accomodate thin copper tape as...
thingiverse
I use this as a battery eliminator for my FT-4XE. It is not really finished or perfect. But it is perfectly functional. It clips in and stays in place as you would expect. I use automotive spade connectors for the contacts. I supply the DC...
thingiverse
An FT-4x battery clip. I use this as a sort of portable charger. It only provides contact spaces for the outer contacts on the back of the battery. I just use a lot of solder to make up the contacts in the clip. Simple, not the best, but it works. ...
prusaprinters
... print without supports. ...This leads to an easier and cleaner print. Printed in PETG.This is a power/volume knob I designed for the Yaesu FT-60. ...I printed mine in TPU but I think PETG would work also.</p><p>This knob also works for the VX-150.</p>
prusaprinters
Many times I went to retrieve my trusty Yaesu FT-60R from my backpack, only to find that the power/volume knob had been bumped and the battery was running down.Removing the battery is not a great solution as it adds hassle every time you want to use...
thingiverse
One of my few complaints about the FT-60 is that I found the squelch dial to be too big, so it would often get bumped and turned to an undesired setting. This is a simple part I made that replaces the dial - it is smaller and harder to turn so it...
thingiverse
Lithium conversion for the Yaesu FT-727R HF/UHF radio using three 18650 batteries, lithium charge controller, and a led voltage gauge. http://mju.io/yaesu-lithium-conversion/ Chassis fitment is a little tight. ...Printed these Z up.
thingiverse
This is a battery holder for Yaesu FT-817, using 3 x 18650 Li-Ion protected cells. ...You need to replace the original battery cover with the 3D printed one.
thingiverse
Fueled by a print I did of someone else's Baofeng battery compartment, I set out in Tinkercad to create my own 18650*** battery compartment for a Yaesu FT-60. This was my first radio, and I can't see spending $20-$40 for replacement batteries for it....
thingiverse
This case is for Yaesu FT-11R, for 18350 elements. The springs had to be placed at the bottom and this is not a good idea, but in this case it is the only way to make the design of the case as simple as possible. ... ...
cults3d
This is a replacement battery charger hole cover. ...Can be modified if youre adding an internal sound interface or somethign!
thingiverse
This is a replacement battery charger hole cover. ...Can be modified if youre adding an internal sound interface or somethign!
thingiverse
I finally got tired of the silly gap left under nearly any third party antenna or adapter on the FT-60 (which isn't flat, so can't be filled with a simple washer) and made a spacer to go on it =] It may fit a FT-50 as well, not certain.
thingiverse
I updated it to - Accommodate a different fuse holder - Deeper wire channels between the positive and negative battery terminals that get connected to allow for the additional wire I have included a schematic of the wiring and a picture of the...
thingiverse
Re-sized for a Yaesu FT-530. ...Added fillet to the base and closed the hole in the back.
thingiverse
This is a side handle for the Yaesu FT-857. ...The handle uses the mounting bracket screw holes on the both sides of the radio body.
thingiverse
stand for yaesu ft-4x radio , this is a fitting for a car mount , but for now only the desktop version , it came out very light so it is best to glue. ... enjoy !
thingiverse
This are feet for the Yaesu FT-991A transceiver. I needed I slightly higher angle then the holder which came with the radio could provide Update: I realized I forgot to mirror one of the feet in the pair file. ...This mistake is corrected in the file...
thingiverse
I recently purchased a Yaesu FT-70Dr radio. I wanted a stand for this radio. I have one for my Radioddity GD-77 and with a slight mod works great on my Anytone AT-D868uv. ... Shout out to the creator of the Radioddity GD-77 stand: ...
thingiverse
This is a cover for the Yaesu FT-991A Transceiver. The print requires a 25cm wide printbed (such as Prusa i3) but no supports. The uploaded version doesn't have the callsign in the front. ... The upper ears can be used for sticking two flat magnets...
cults3d
I recently purchased a Yaesu FT-70Dr radio. I wanted a stand for this radio. I have one for my Radioddity GD-77 and with a slight mod works great on my Anytone AT-D868uv. ... Shout out to the creator of the Radioddity GD-77 stand:...
thingiverse
A replacement knob for the Yaesu FT-50R My radio was missing it's knob, so I designed one to replace it. It's designed as a tight fit which meant I had to tweak the horizontal expansion settings to get it to fit on my printer. I ended up going for...
thingiverse
I wanted a way to attach my HT to my bike. ...As there are lots of GoPro mounts for handlebars I decided to make a GoPro FT-1D mount