yaesu ft 767gx 3d models
6377 3d models found related to yaesu ft 767gx.thingiverse
My Yaesu FT-767GX was missing the covers for emty modules places. ...So i make this for better appearance.
thingiverse
Re-sized for a Yaesu FT-530. ...Added fillet to the base and closed the hole in the back.
thingiverse
This is a side handle for the Yaesu FT-857. ...The handle uses the mounting bracket screw holes on the both sides of the radio body.
thingiverse
stand for yaesu ft-4x radio , this is a fitting for a car mount , but for now only the desktop version , it came out very light so it is best to glue. ... enjoy !
thingiverse
This are feet for the Yaesu FT-991A transceiver. I needed I slightly higher angle then the holder which came with the radio could provide Update: I realized I forgot to mirror one of the feet in the pair file. ...This mistake is corrected in the file...
cults3d
I recently purchased a Yaesu FT-70Dr radio. I wanted a stand for this radio. I have one for my Radioddity GD-77 and with a slight mod works great on my Anytone AT-D868uv. ... Shout out to the creator of the Radioddity GD-77 stand:...
thingiverse
I recently purchased a Yaesu FT-70Dr radio. I wanted a stand for this radio. I have one for my Radioddity GD-77 and with a slight mod works great on my Anytone AT-D868uv. ... Shout out to the creator of the Radioddity GD-77 stand: ...
thingiverse
This is a cover for the Yaesu FT-991A Transceiver. The print requires a 25cm wide printbed (such as Prusa i3) but no supports. The uploaded version doesn't have the callsign in the front. ... The upper ears can be used for sticking two flat magnets...
thingiverse
A replacement knob for the Yaesu FT-50R My radio was missing it's knob, so I designed one to replace it. It's designed as a tight fit which meant I had to tweak the horizontal expansion settings to get it to fit on my printer. I ended up going for...
thingiverse
I wanted a way to attach my HT to my bike. ...As there are lots of GoPro mounts for handlebars I decided to make a GoPro FT-1D mount
thingiverse
My Yaesu FT-60 had a difficult to use volume knob, so I got inspired by this version: https://www.prusaprinters.org/prints/137075-yaesu-ft-60-volume-knob-v2/files And created my own.
thingiverse
Battery replacement cover for the Yaesu FT-817/817ND and probably the FT-818. The published part has no callsign added. ...You can add this on Tinkercad.
thingiverse
Desktop stand for the Yaesu FT-3DE and probably FT-5DE, too (same case ?) with standard battery. ...No special print settings needed, example printed on Anycubic I3 Mega without supports.
thingiverse
The is a desk stand for the Yaesu FT-100D. It raises the front, so it gives the LCD better visibility. ... The curved slot require support.
thingiverse
Yaesu FT-817/818 stand. Stand is assembled using 3mm countersunk bolts and nuts. ...I used velcro strap to hold radio to stand.
thingiverse
Replacement Dial Knob For Yaesu FT-8900R. ...I remixed the one the other guy made because it didn't fit on my radio.
thingiverse
Shelf bolts between my AnyTone AT-578 radio rails to protect and hold Yaesu FT-1500M that I use for packet radio. Side rails for AnyTone AT-D578UV, and Yaesu FTM-400 (probably FTM-100)...
thingiverse
A remote facia mount and desk stand for the Yaesu FT-857D. Added optional microphone holders. The curved one can be attached to side of facia mount. Added desk stand for the facia. ...Let me know if it requires tweaking.
thingiverse
This is a clip on pad for the tuning dial of a Yaesu FT-450D. I designed it during the 2020 ARRL Phone Sweepstakes to help with tuning around. ...This will fit radio dials that are 35mm in diameter.
thingiverse
First draft of guards for a Yaesu FT-450D. This has not been printed yet, but the measurements work. ...It should fit on an Ender 3 bed at 45* easily, but does fit, just barely, without rotating.
thingiverse
Quick and simple desktop stand for Yaesu FT-7900 VHF/UHF FM mobile transceiver. ...For better grip and to lift up the transceiver rubber feet is a must (see photo).
thingiverse
This parts are designed to make a protection for the knobs of the Yaesu FT-817 or FT-818, using the stock screws and you don't need to adjust screws length. You can print the stand separately, which is removable when you move for mobile use. ...
thingiverse
Front cover for Yaesu FT-991/A The scaled stl file is a slightly snug fit the not scaled version is better with foam draft excluder tape to make it a nice snug fit. Fusion 360 file included . if you re-mix it please post as such. ... Have fun.
thingiverse
Yaesu FT-ONE was missing a side foot. Measured up one of the remaining original feet and sketched up and printed up a new one. 15mm base with 10 degree taper to ~12mm. 8mm 'tall.' 3.2mm hole in the recess for screw. Can scale in your slicer if...
thingiverse
This is a remix of very well designed Yaesu FT-4X Battery box from thazlett, https://www.thingiverse.com/thing:4446212 i just add some tollerance and beef it up to be less flexible. Also i lowered the contacts sims to accomodate thin copper tape as...