yaesu ft 817 battery 3d models
76729 3d models found related to yaesu ft 817 battery.thingiverse
Battery replacement cover for the Yaesu FT-817/817ND and probably the FT-818. The published part has no callsign added. ...You can add this on Tinkercad.
thingiverse
This is a battery holder for Yaesu FT-817, using 3 x 18650 Li-Ion protected cells. ...You need to replace the original battery cover with the 3D printed one.
thingiverse
I updated it to - Accommodate a different fuse holder - Deeper wire channels between the positive and negative battery terminals that get connected to allow for the additional wire I have included a schematic of the wiring and a picture of the...
thingiverse
Ho acquistato questa radio usata e non ho mai avuto il perno di blocco per lo sportello del vano batterie del YAESU FT-817. L'ho realizzato con FUSION 360 e stampato con ender 3. Non posso dire che sia precisissimo probabilmente non a causa...
thingiverse
Yaesu FT-817/818 stand. Stand is assembled using 3mm countersunk bolts and nuts. ...I used velcro strap to hold radio to stand.
thingiverse
This parts are designed to make a protection for the knobs of the Yaesu FT-817 or FT-818, using the stock screws and you don't need to adjust screws length. You can print the stand separately, which is removable when you move for mobile use. ...
thingiverse
... quite nicely . I've used this for about a year doing SOTA and it has worked great enjoy. There is no difference between the 817/817ND/818 apart from the name on the front Please don't remove my call sign from the inside , it "is" all my own work.
thingiverse
This is my first attempt at "table legs" for keeping my Yaesu FT-817 and it's paired LDG Z-817 tuner together. Here, show with just rubber bands, the LDG is kept on top of the 817 and cannot slide off. These are the start of a "man pack" for this...
thingiverse
I designed a simple adapter to replace or add a shoulder strap to a FT-817 or FT-817ND. You will only have to buy strap for this. The stock screws work just fine! ...Print Settings Printer: Monoprice Select Mini ...
thingiverse
Perhaps someone from the owners Yasu FT-817 like the decision. The body is not designed for manpaсk use, for this is a more appropriate structure. ...Print Settings Printer: Picaso 3D-Designer ...
thingiverse
Front feet for Yaesu FT817 to raise the front of the radio face to a better reading angle. ----Update------ Redesigned to make them a little more sturdy. ... Added more source files
thingiverse
This is a remix of the case, which was orignally created by slider235. ...I just added a opening for charging the Windcamp battery without the need of taking out the hole radio.
thingiverse
A clip allowing to attach a neck strap to your Yaesu FT-817/818. ...A necessity when hunting satellites, quite useful for /p activities too.
thingiverse
This parts are designed to make a protection for the knobs of the Yaesu FT-817 or FT-818, using the stock screws and you don't need to adjust screws length. You can print the legs separately, which is removable when you move for mobile use. If...
thingiverse
This is a case/enclosure for YEASU FT-817and FT-818. I designed this in a way that no support is needed and also in parts that can be printed on any printer including Prusa MINI. To assemble you need following items: 1- 30 x Brass Inserts M2 x...
prusaprinters
<p>The standard tuning knob is too small for my fat fingers, so I made this. You will need a short 3mm screw to fix it to the shaft.</p> <p>Print with supports, in fine resolution. ...PLA is OK</p> <p>If you download this and use it please hit LIKE!</p>...
thingiverse
The standard tuning knob is too small for my fat fingers, so I made this. You will need a short 3mm screw to fix it to the shaft. Print with supports, in fine resolution. ...PLA is OK If you download this and use it please hit LIKE!
thingiverse
This is Tilt-Up stand for YAESU FT-817/818. Print two of each part. Need 4 tapping screws 3x8 for assemble. There is a problem that the microphone connector is hidden when stored. ... Now I'm thinking about measures.
thingiverse
Side rails for holding two Yaesu FT-817 and 817ND to provide protection to front and back. Will require screws on the side to be replaced with longer screws. ... Rails were designed with these screws: https://amzn.to/2LyODy6 Best results were...
thingiverse
Side rails for Yaesu FT-817 and 817ND to provide protection to front and back. Will require screws on the side to be replaced with longer screws. ... Rails were designed with these screws: https://amzn.to/31wHx2B Best results were with the...
thingiverse
This is a remix of very well designed Yaesu FT-4X Battery box from thazlett, https://www.thingiverse.com/thing:4446212 i just add some tollerance and beef it up to be less flexible. Also i lowered the contacts sims to accomodate thin copper tape as...
thingiverse
I use this as a battery eliminator for my FT-4XE. It is not really finished or perfect. But it is perfectly functional. It clips in and stays in place as you would expect. I use automotive spade connectors for the contacts. I supply the DC...
thingiverse
An FT-4x battery clip. I use this as a sort of portable charger. It only provides contact spaces for the outer contacts on the back of the battery. I just use a lot of solder to make up the contacts in the clip. Simple, not the best, but it works. ...
thingiverse
FT-817 battery holder with BMS - - - Parts: Metal AAA Batteries Spring Contact Plate Terminal https://www.aliexpress.com/item/4000092167957.html?spm=a2g0s.9042311.0.0.343f33edrXt5X5 BMS 3S 10A 12V Lithium Battery Charger Protection Board Module for...
thingiverse
I've designed this thing to keep knobs safe while operating outdoors. Very easy print, is held in place by carrying strap that came with a radio. Also doubles as a stand while sitting on a table. ...Back frame (red one as seen on pictures) can be found...
thingiverse
I've designed this thing to make sure I'm not going to damage connectors on a back of a radio while operating digital modes outdoors. ...Especially useful while hiking as there is no need to set up rig every time You want to use it.
prusaprinters
<p>Supports might be required under the V2 knob spinner. ...Used Prusaslicer's Paint-on Supports.</p><p>Added a new version (V3) that brings the ring closer to the center, avoiding any need for supports that might affect the knurling pattern.</p>
thingiverse
Side rails that fits in the yaesu cover! And you can use the original screws! Remember to mirror one before printing. ... Support required!
thingiverse
Lithium conversion for the Yaesu FT-727R HF/UHF radio using three 18650 batteries, lithium charge controller, and a led voltage gauge. http://mju.io/yaesu-lithium-conversion/ Chassis fitment is a little tight. ...Printed these Z up.