yaesu ft891 side rails 3d models

3D printed radio holders for the Yaesu FT-70D

PTT switch adapter crafted for Yaesu and Kenwood radios, meticulously replicated from original Yaesu MH-31 design specifications.

Suitable for Yaesu vx-7r. May be suitable for other devices. ... Need supports for better quality

This is a recording for the Yaesu VX-6R radio system.

This is a lug that mounts on the back of the Yaesu mic. ... Might fit others as well.

Remixed the Baofeng UV5R RAM-mount cradle to widen the belt clip slot a bit to fit the Yaesu FT5D.

Microphone mount and microphone button. ... This should work on most Yaesu radio mics. e.g. ...MH series microphones.

Re-sized for a Yaesu FT-530. ...Added fillet to the base and closed the hole in the back.

a fan mounting bracket/wedge/adapter to securely mount aftermarket fan in the yaesu FT891. Fits snugly in the fan slot without needing tape or anything. noctua fans are substantially quieter and better at cooling when ragchewing I used petg and...

This is a simple Yaesu FT-8900 YSK-8900 faceplate holder, used as part of the separation kit to allow customization with your preferred attachment.

Set of feet for the Yaesu FRG7. Needs 2 x M4x10 and 2 x M4x25 philips screws. ... Design on tinkercad : https://www.tinkercad.com/things/2dMbBCXfwz6

A sleek and simple cradle for the Yaesu FT2D handheld radio. ...Designed to keep your radio secure and stable while minimizing obstructions to controls and audio output.

Using a rechargeable battery of the type 14500 and a spring, I will recover my old and beloved YAESU VX-1. ...A bit of fine sandpaper is necessary.

Visit my website at www.linuxwolfpack.com to access additional details and other models associated with my current project, specifically a 3D model of the Yaesu FH-2.

Корпус переходника sma для подключения к радиостанции yaesu антенны от baofeng и других. Переходник универсальный. ...Печатать без поддержек 100 процентное заполнение.

Here's a comprehensive protection system designed specifically for the Transceiver Yaesu FT 817 and 818. Protecting your Transceiver Yaesu FT 817 and 818 is crucial to ensure reliable performance and extend its lifespan. ...The following protection...

This is a remake of: https://www.thingiverse.com/thing:1703604 Brand New Design for Wider and Thicker Yaesu FT1XD SHB-13 Belt Clip. ...The original design for the Yaesu FT1D belt clip was not suitable due to its wider and thicker build.

The sides are attached to the top and bottom with four #6 by 1/2" sheet metal screws on each side. The fan can be secured with #8 by 1/2" sheet metal screws if you don't have eight of the PC fan screws. ... Instructions ABS, standard...

Replacement refers to a specific term associated with the Yaesu FT-100, which is a model of amateur radio transceiver. ...This terminology might be unique or limited to a particular group.

A small table stand for the Yaesu FT5-DE/DR handheld radio.Have not tested with earlier models, but should fit FT3D at least. Printing:No special considerations, this should be an easy one to print.

HT Radios have a tendency to fall over when sitting on the desk. ... This stand designed for Yaesu FT3D. ... I added stick-on rubber feet from a hardware store to keep the base from sliding around on a flat surface.

A small table stand for the Yaesu FT5-DE/DR handheld radio.Have not tested with earlier models, but should fit FT3D at least. Printing:No special considerations, this should be an easy one to print.

CatKnobz bracket STL file to suit Yaesu FTDX10. ... The knobs sit back a bit but there is ample room for my fat fingers & I can access the tension adjustment under the VFO knob OK.

Designed specifically for cables that don't secure with screws on your Yaesu radio. ... Modeled perfectly for use with cables like the Sena SC-A0114 2-Way Radio Cable, featuring a single pin connector.

stand for yaesu ft-4x radio , this is a fitting for a car mount , but for now only the desktop version , it came out very light so it is best to glue. ... enjoy !

I Doubled up on the Support Arms/Rails when I printed Chrlee's Microscope Stand for myself earlier this year, so I knocked out some supporting Arms that have the Mating Slots and Grooves on both sides... ... ...Simple, But it makes Chrlee's...

I'm thrilled to share my latest 3D printing triumph with you all - a custom bracket for my trusty Yaesu handmike that I use on the road. ...This sleek design fits perfectly in my car and securely holds the microphone in place just as intended.

I recently purchased a Yaesu FT-70Dr radio. I wanted a stand for this radio. I have one for my Radioddity GD-77 and with a slight mod works great on my Anytone AT-D868uv. ... Shout out to the creator of the Radioddity GD-77 stand:...

This is a tripod for the Yaesu ATAS-25 portable HF antenna. It requries a 1/4-20x1 bolt to hold the tripod to the base of the antenna. ... I like to add a washer on the head of the bolt, but it's probably not necessary.

This holder provides a secure fit for the Yaesu microphone, holding it firmly in place with a snug grip. The addition of screw holes allows for easy mounting options virtually anywhere. ...Its uncomplicated design also makes it highly adaptable,...