yeasu 857d 3d models
42 3d models found related to yeasu 857d.thingiverse
This is only for ft-857d, there's plenty of ftm-100d models floating around. The bottom square hole is for 19.5x13.5mm rocker switch, and the other version has also a 9mm round hole for fan control. 90x90x25mm case fan was used. 3 sets of holes...
thingiverse
After years of lacking one knob on my Yeasu FT-480r, I designed one myself. Now it looks complete again. I printed multiple knobs the same time and used a brim. ...I printed them in white but it looks a bit too new now for the set :) Hope this...
thingiverse
A remote facia mount and desk stand for the Yaesu FT-857D. Added optional microphone holders. The curved one can be attached to side of facia mount. Added desk stand for the facia. ...Let me know if it requires tweaking.
thingiverse
I needed a mobile mounting bracket for my Yaesu FT-857D. I bought my radio used and I did not get the bracket with the radio from the previous owner. Several of the online ham stores want $75 + for the mobile remote mounting kit which has the...
thingiverse
A "separation" remote head mount for the Yaesu FT-857D. Final version. This version uses a "bump" on the end to keep the head in place. It also has holes on the top and bottom to mount to a desk, unlike the Yaesu version. Of course, this is also...
thingiverse
This would probably work for any mobile-style radio with a mounting screw on the side, but I designed it around the FT-857D. The Fusion 360 design file is included if you want to make changes. ... You'll need a 6mm M4 screw to attach it to one of...
thingiverse
Bracket for Yaesu FT-857D head unit. Has been tried and printed, may need some fine tuning as its a little tight but will work after "de-burring." Open SCAD file available to change things. ...You need the FT857DNUB.SCAD file to render the model.
thingiverse
Front support for separation kit FT-857D with adaptation for Gopro and similar supports. ...Remixed from G0WFV by PY2LCD.
thingiverse
This is the piece that is inserted into the radio for the rotating "select" knob. Mine broke and replacements are not available for purchase. This was designed using tinkercad and I believe I printed it at 98% size. it did require a small amount of...
thingiverse
Two-piece side rails designed for the Yaesu FT-857D and FT-857 mobile radios (also fits the FT-891). May be mounted to both sides of radio. ... Some warping and delamination of PLA was observed after a few months of mobile radio operations during the...
thingiverse
Here is a simple stand for the FT-8900R. This stand was inspired by, but not derived from, the FT817 stand by S57RZ (thing 219316). I created my stand in OpenSCAD rather than sketchup. Besides making it fit the FT-8900, I also made the foot plate...
thingiverse
Designed this to hold my FT-891 remote head for my "Go Box".
thingiverse
These should fit both the FT-991 and the FT-991a models. They will fit diagonally on a CR-10 bed, but will have to be split for smaller printers. I make mine out of Pro-PLA and they have held up pretty well. I would print them with as many walls as...
thingiverse
to replace broken belt clip for the Yeasu Vx5r HT HAM radio. ... printed in PETG
thingiverse
Yeasu FT-60 Wall Mount PS: Form factor is perfect, radio fits in, all within specks after PLA print..
thingiverse
Microphone holder for the Yaesu MD-1 desk Mic. ... May also fit on other Yeasu microphone models.
thingiverse
Stand for the Yeasu FTM-400 mobile HAM Radio. A single ~4mm screw and nut is required to combine bottom and top Part. + Adjustable tilt Angle. + No Yaesu suction mount required. Made while learning Fusion 360. Works fine for me. ...
thingiverse
Two versions of microphone hanger clips for ham or CB radio. ...Designed for thin glass desktop edges. The pictured uses are for a Yeasu FTdx10 and a Xiegu X6100 microphone but fit many others.
thingiverse
This is a holder for amateur ham radio Yeasu microphones. I used my design for a 3way shelf holder (18mm thick plywood) and added a microphone holder area. My Yaesu mics fits perfectly as you can see on the pictures. Anytone 578 mic is a tight...
thingiverse
This is an updated rail for the Yeasu FT-100 HF/UHF/VHF ham radio. I found some rails but wanted something a little more modern/different so i designed these based on others i had seen online. ...I hope you enjoy.
thingiverse
Update : by enlarging hte 'gap' just a little bit it is also suited for a Yeasu microphone. ... Instructions Designed with OpenSCAD, printed with the Velleman K8200 printer with 3mm PLA Print the bracket...
thingiverse
Holds a Yeasu FT3DR Radio with access to the touch screen and a few other button. Nice Flat back that can be attached to a flat spot on your dash or other mount with double side adhesive. ... Should print perfectly fine without supports.
thingiverse
Here is a really practical tool for mounting a Yeasu FT-2D handheld radio in the cup holder of VAG vehicles such as: Audi, VW, Seat and Skoda. Tested on an Audi A6 C5 from 2002. The holder is equipped with a snap-in button for the belt clip so...