ywrobot 4 relay 3d models

http://www.thingiverse.com/thing:312762 I added support for small openings that can be removed after printinghttp://www.3dhubs.com/milan/hubs/christian

For Arduino or Rapsberry.....

A case for the raspberry pi 3 and a 4 channel relay module. ...I use it for Octoprint.

Enclosure for ESP 8266 D1 Mini with 4 way Relay module HW-316 and MP 1584 step down module.

A case for the raspberry pi 3 and a 4 channel relay module. ...I use it for Octoprint.

Hook up your Wemos D1 mini to a 4-way relay board and unlock the full potential of ESPEasy.

Support with 5mm clearance for fixing to a 2020 profile, designed for a 4-reed solid-state low-level relay board. ...Relays used in the automatic shutdown system of the printer.

Manufactured specifically for use with a 4-channel relay card, this enclosure shields the relay from physical collisions and provides the user with a means to adjust and fine-tune their setup.

This inexpensive USB 12V relay module is a purchase from Amazon, specifically the SainSmart 4-Channel 12V USB Relay Board Module Controller designed for automation and robotics applications. ...You can find it here:...

... ...A RPi Zero and JBtek 4 Channel Relay frame can be found on Thingiverse at https://www.thingiverse.com/thing:4027202. ...The original project page is located here: https://www.codemacs.com/raspberrypi/howtoo/raspberry-pi-zero-w-frame.9324961.htm.

Top case for RPI3 and Keyestudio 4 relay hat: I've designed it to be expandable, just like the Mykorhiza model, with four holes to accommodate LED indicators for each relay. Spacer between RPI and relay hat. Top fullfill.stl - this design is...

... from seanmfink's remix of thehair's relay case. ...This fits the JBtek 4-channel relay perfectly. Removed the mounting wings and replaced with a 20x20x5 2020 profile mount. ... Used an M4 cap head screw, slightly recessed to mount to extrusion.

Case to hold Raspberry Pi 4 and a 4 relay board.I used it to hold my printers Raspberry Pi and the relay board, to power an enclosure LED light switched on/off by Octolight (https://plugins.octoprint.org/plugins/octolight)Full assembly instructions...

This model fits the Tuya 4 channel relay module similar to: https://a.co/d/28Jme6A but also available from Aliexpress and other sources at a much lower cost.

This is a special enclosure for Relay 4, where you can hook up power using an RJ45 jack and exercise total control over the tuner via Arduino Uno or Mega.

Little remix (it's redesigned by me for scratch but it's the same thing. ... Its designed for Raspberry Pi 4 with metal case. It have support for 1CH relay for power ON/OFF and some drill for cable management.

... out, then having to figure out where they go again. Works with these standard cases: Raspi: https://www.thingiverse.com/thing:922740 4-Channel Relay: https://www.thingiverse.com/thing:957292 8-Channel Relay: https://www.thingiverse.com/thing:336948

This is a custom enclosure built to house an LC-tech 4-channel relay module and a Nice Flor-S remote control. The box provides a secure and organized space for both components, making it easy to integrate them into any setup. For more information on...

... You can access the detailed instructions here: https://www.instructables.com/id/4CH-Relay-board-Controlled-With-Push-Buttons/. The custom case I've designed is specifically for mounting the RPI 3B+ and the 4-channel relay board together efficiently.

I designed a mounting bracket for the Raspberry Pi Pico, to mount it onto a 4-Channel relay. The bracket has 3 holes to mount the Pico with M2 bolts. The bolts screw right into the plastic, no threads needed. I use these setup as a simple...

Raspberry Pi Zero and JBtek 4 Channel Relay frame are used for home/garden automation projects. This setup was specifically utilized for the Smart Garden project. The Raspberry Pi 3 frame is available at https://www.thingiverse.com/thing:4027212.

Shrinked 4 relay case, to fit boards sold by Conrad Electronic with the label "Baite" and model name "BTE13-004". Closed not required holes in the cover, to improve protection from dust and debris for my usecase. Printed cover in transparent PLA to...

... I started create my own floor heating control system. ... I dont found simple box for Pi Zero and 4 relay module, so I created one. Print time with my settings ~7 hours 30 mins. Recommend supports for cable ports. ... I will create cover soon too.

... create my own floor heating control system. ... I dont found simple box for Pi Zero and 4 relay module, so I created one. Print time with my settings ~7 hours 30 mins. Recommend supports for cable ports. ... I will create cover soon too.

Parts List: 1x Raspberry Pi Model 2 or 3B 1 x SainSmart 4-Channel Relay Module: https://www.amazon.com/gp/product/B0057OC5O8/ref=oh_aui_detailpage_o00_s02?ie=UTF8&psc=1 1 x Enclosure Bottom Stacked 1 x Enclosure Top Stacked w/Supports 2 x Board...

Remix of https://www.thingiverse.com/thing:865599 to fit a power module attached to an arduino or arduino's sensor shield V4 like in the photo. Only need 2 M3 short screws as 8mm screws. ... Log: ------- * 15/12/2018: Added new version...

Just another model I thought people might find really useful. I am going to be using one of these models to control the power to an LED strip or two that I plan to mount to my CR-10, so I thought enclosing it in a small case would be a great idea. I...

I used it to hold my printers Raspberry Pi and the relay board, to power an enclosure LED light switched on/off via Octoprint using the Octolight plugin (https://plugins.octoprint.org/plugins/octolight) Full assembly instructions here The case is...

I used it to hold my printers Raspberry Pi and the relay board, to power an enclosure LED light switched on/off by Octolight (https://plugins.octoprint.org/plugins/octolight) Full assembly instructions here The case is held together by 4 screws...

You'll also need to purchase the MKS GEN 1.4 control board from Amazon (https://www.amazon.com/Witbot-MKS-Gen-Controller-Integrated-Mainboard/dp/B01LW1Y1D2/ref=sr_1_4?ie=UTF8&qid=1537987592&sr=8-4&keywords=MKS-Gen+V1.4+Controller) and a two-channel...