z sync kit for creality cr series 3d models

So I looked for the spectacle kit that I was sure would exist…http://web.archive.org/web/20201202214246/https://www.winc.com.au/main-catalogue-productdetail/3m-6878-spectacle-kit/25042148A$243.00 ?!And it's just a bent piece of wire and a couple of...

I added height to this knob to clear the top of the frame braces I just printed and installed on my CR-10 https://www.thingiverse.com/thing:2123233

... measurements relative to the section coupling with the 2020 extrusion. The fusion 360 file used for these modifications is included, allowing users to incorporate stabilization braces, alter dimensions, or implement other changes as desired.

Durable and solid mounting ears for CISCO C1000 series routers v2 with place for original screws

Remix of Andraxis To assemble this entire kit, you will need to print: 20x cableChain_link_v3.stl 20x cableChain_linkCover_v2.stl I printed this kit in ABS+ Sunlu Gris. This means it can withstand high temperatures inside my enclosure. ... _ _ _ _ _ _ _...

We're offering a filament lead that's easy to install on the Z-axis, perfect for use with your Creality CR-10 printer - just take a look at the images to see how it fits. I built this guide using PLA and filled it in at 50%. ...I strongly suggest...

This z-axis sensor mount substitutes the standard mount, but its holes for mounting micro switches are 1mm lower, resulting in the print head falling 1mm short. The G-code used was from a PLA+ 210-degree print on my CR10S. I've included the Fusion...

I'm going to attach the webcam mount to the Z-axis under my Creality CR-10. Check out this video for a clear guide: https://youtu.be/OYypYcAOfmQ or https://vid.me/Kwf2q. ...I've added versions 2 and 3, which you can see in the Shape document here:...

This a small remix of the awesome "Z-stop Cover with clips" design by @Solitary47. I pretty much added a hole on the part so I can see the light from the red LED at the Z stop. In order to make it look nicer, I used a little bit of hot glue while...

I've only shared the files for the two parts I modified; please refer to the linked remix of the original clip-on design for its well-designed mounting bracket on the z-axis. Note that in the provided image, the original designer's clip-on bracket...

Added Mount with pilot hole for forming threads with screw. There is little force on this part, so it should work just fine. 3. Added twist-nut style keeper to the backside of the bracket to keep it in the t-slot. It is inteneded to raise the...

Modify 360-degree ventilation around the nozzle for 3D Printer Creality CR-10S.\r\nWithout supports.\r\n\r\nHigh quality - High quality\r\n\r\nModification for 360-degree ventilation around the nozzle for 3D Printer Creality CR-10S.\r\nNo Supports.

This upgrade boosts the living conditions for Creality printers by taming the unruly z-rod movement within its enclosure at the printer's top. ...The result is a notable decrease in noisy rattling, without any impact on print quality itself.

Motor Mount for Ender-3 Printers and Similar 3D Printers This adaptable motor mount is designed to be easy to print while allowing for proper motor cooling. For those who prefer a more secure installation, an extended version of this design...

I designed a custom setup specifically for my three-in-one-out NF-TH01 switching hotend. ...The extruder I'm using is the MPR5, which can be sourced from aliexpins dot com.

Hardware needed: 1/2" Aluminum pipe, ~20" length for each side for the SV01, be sure to measure if you have a different printer. x4 M3x10 Screws x4 M3 Hex Nuts x12 M5x12 Screws x12 M5 T-Slot Nuts Can be printed in PETG, ABS, and Nylon. ...PLA...

You will need to remove the bearing blocks at the top of the lead screws (if you have them), since the top half needs to be screwed in at that location! Hardware needed: 1/2" Aluminum pipe, ~20" length for each side for the SV01, be sure to measure...

Joined togheter: Flexible Filament Extruder Upgrade for Creality CR-7, CR-10, Afinibot A5, A31 by joshvv, published Mar 1, 2017 CR-10 Hotend Cable Management by donnyb99, published Mar 11, 2017

Joined together by the community: Flexible Filament Extruder Upgrade for Creality CR-7, CR-10, Afinibot A5, and A31 by joshvv, published March 1, 2017 CR-10 Hotend Cable Management by donnyb99, published March 11, 2017 Print Settings: Printer:...

For flashing SimonK firmware onto a ESC, access the ATMega's pins; however, HK Blue Series 12A lacks extra pads. Therefore, alternative methods to soldering wires on µC legs must be found. I utilized this technique for my micro quadrocopter:...

The lead screw wasn't binding but felt a bit too tight, so I created a new z-mount and now it's running very smoothly. I've been able to adjust for perfect alignment. The motor mount screws are also the same size. ...However, the T-nut screws need to be...

This is a 3D printable shockmount for the Austin Microphones ribbon microphone kit, which also works with any other microphone having a 1.5-inch diameter. diyribbonmic.com/diykits/ features this fantastic-sounding microphone. ...This print will fit on a...

Support for neon lighting on Creality CR-10/CR-10S/mini or any machine with a 2020 or 2040 profile allows you to secure the LED neon lights available at Action stores. ...This results in minimal loss of print height.

Design a Customized Model for the Creality CR-8 3D Printer. Visit Thingiverse to Access the Remix Version Now! ...https://www.thingiverse.com/thing:4119215

Extruder knob designed specifically for the compact Creality CR-100 3D printer. ...Crafted with precision, this custom-made component was conceived in SolidWorks software.

I'm looking forward to seeing your detailed explanation of this concept!

... with a blade sized 39x2mm or smaller.Print as oriented in the STL. Infill and supports optional. Print SettingsPrinter Brand:CrealityPrinter:CR-10 SmartRafts:NoLayer Adhesion:Brim (optional)Infill:10% (optional)Filament:Creality PLA CR Series

This is a soundproof cover for the rear exhaust fan on a CR-X base. ... Reference https://www.youtube.com/watch?v=RRbvASlom4A&t=91

Custom Z Ichimonji for Rockman Zero Mega Armor model kits.Note, the scale is not perfect, and the artwork is a little fuzzy so I did what made sense. ...Feel free to remix it if desired.

Parts and tool trays designed specifically for the Creality CR-10 bed, featuring one standalone tray and two interlocking trays that perfectly fit together. This innovative design was inspired by a modified version of another Creality CR-10 tool...