z31 nissan 3d models
4741 3d models found related to z31 nissan.thingiverse
This is a harness or vacuum hose clip for the Z31 300ZX, but I'm sure Nissan used it on other models. Apparently these are NLA and people want them, so I made a copy. ... PN#: 14962M or 24220B0701
prusaprinters
This is a harness or vacuum hose clip for the Z31 300ZX, but I'm sure Nissan used it on other models. ...Apparently these are NLA and people want them, so I made a copy.</p> <p>PN#: 14962M or 24220B0701</p> Category: Automotive
thingiverse
Front parcel shelf clip and pin set for 84-89 Nissan Z31
cgtrader
Nissan Z31 Kouki 3D model Features: Real world scaled.(Units in milimeters) Textures included. -Salon. ...Suitable for animations and architectural visualizations.
thingiverse
Rev2 design based on the original design, not reinforced or necessarily optimized for 3D printing. ...This is for any 84-89 Nissan Z31 that had the parcel shelf option between the rear strut towers.
thingiverse
Rev1 design based on the original design, not reinforced or necessarily optimized for 3D printing. ...This is for any 84-89 Nissan Z31 that had the parcel shelf option between the rear strut towers.
thingiverse
... and prevent breakage in the common areas. ...This is for any 84-89 Nissan Z31 that had the parcel shelf option between the rear strut towers. ... The photo shows a early print done with PLA and it did sag a bit where i did not have adequate cooling.
thingiverse
Nissan 300zx Z31 T-Top release clip. I modeled this after mine broke. ... Printing: Use ABS for heat resistance.
thingiverse
Spare tire screw knob for a 1984-1989 Nissan 300zx, Z31 chassis. Functions the same as an OEM screw with the same thread pitch and design. ... If anything fits a tad snugger.
thingiverse
Another cup holder option to rival the others out there. Personally I like it tucked away in the center console. Been using this design in all my Z's for some time now. Figured I should share. Leaves enough space to still put junk in the...
thingiverse
Screws for plastic cover for the spare tire in the hatch with a small Z logo on top of the screw.
thingiverse
1984 - 1986 Nissan 300zx replacement interior panel pin for left rear taillight.
thingiverse
Replacement thumbscrew for the 1984-1986 Nissan 300zx spare tire/right rear taillight panel cover. This is a double helix thread like the original panel screw! ...A single thread design WILL NOT work with the OEM receiver clip.
thingiverse
1984-1989 Nissan 300ZX T-Top Shade Fastener/Clip. This will fasten into the factory T-Top shade receivers. ***Edit*** Base STL is now included Modeled after the factory piece to closely resemble. The factory piece uses a small metal C-clip to...
thingiverse
This is a door rod holder for some 80s-90s Nissans, I designed this for use on a 1988 300ZX, but works on other models from my understanding. I designed the top part that holds the rod to be beefier than the original, so it shouldn't break as easily...
thingiverse
This is a close interpretation of the lower rubber grommet/pass-thru section the forward T-top drain tubes (76990-03P00) on the Nissan Z31 300ZX. The 10mm OD polyvinyl tubing runs down the A-pillar and then is glued into this black rubber piece which...
thingiverse
... ...The Z is designed after the Zenki style of "Z" used for Z31's (1984-1986). There is an exact copy of this model designed with the Kouki "Z" style as well. The stl is free to download for personal use only. Do not try to make money off my designs.
thingiverse
... ...The Z is designed after the kouki style of "Z" used for Z31's (1987-1989). There is an exact copy of this model designed with the zenki "Z" style as well. The stl is free to download for personal use only. Do not try to make money off my designs.
cults3d
Body Design for scale 1:24 / 1:25. ... This can be scaled up for 1:18 and 1:10 or even bigger.
thingiverse
New cover snaps over latch mechanism. ...It's a pretty tight fit so I recommend PETG, PLA could snap. For Z31 Nissan
thingiverse
Update: I added the Double Din Piece, it's not perfect but should do the job, this will all require some good post fab to make it look and fit correctly This is a Bezel Replacement for a 1980's Z31 300ZX. It should fit all Z31. You will need a bed...
sketchfab
https://prof-decor.com.ua/product/poliuretanovi-viroby-ta-dekory/molding-nmc-arstyl-z31-2m
thingiverse
The AIV is the Air Induction Valve that sits behind the driver's side headlight on the Z31. These two plugs are to plug the holes left behind on the intake boot, and to plug the line coming off of the AIV (the hose that comes off of the side of...