zalman zm mic1 3d models
228 3d models found related to zalman zm mic1.thingiverse
I bought the Zalman ZM-MIC1 due to good reviews to cost ratio. Gotta admit for under 10 bucks it's amazing, better than my $100 gaming headset's mic. The biggest drawback was the built-in clip isn't useful for my general purposes, so I designed this...
thingiverse
A small adapter to mount a Zalman ZM-MIC1 to [petejohnsons'](https://www.thingiverse.com/petejohnson/about) Tiny Tripod. ... The clip is based on [xToxicInferno's](https://www.thingiverse.com/xToxicInferno/about) Zalman ZM-MIC1 Clip.
thingiverse
Customized version of http://www.thingiverse.com/thing:1060861 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=1060861 Instructions Using the following options: INF =...
thingiverse
A simple adapter to mount the microphone to the modular mounting system. ... This is a remix of the Modular Mounting System: https://www.thingiverse.com/thing:2194278
thingiverse
... целой, со всеми выступами и углублениями. Работает как и оригинальная с щелчком. The leg for the Zalman ZM-K200M keyboard. Modeled on the remaining whole, with all the protrusions and depressions. ...Works like the original one with a click.
thingiverse
Want to convert your AKG 121 Headphones and a Zalman ZM-MIC1 Microphone into a Headset? Just use a piece of 3mm Filament and this printed part. Easy. ...:)
cgtrader
A model of the Zalman ZM-GM1 USB laser gaming mouse. Modelled in using surfaces SolidWorks and rendered using KeyShot. This is an external model only, no internal electronics are modelled. ...
thingiverse
This is a microstand for clip microphones especially for zalman zm-mic1. I printed the stand out of PLA with a resolution of 0,15mm and 15% infill and it works perfektly. On the bottom of the stand is a groove for an anti-slip ring. ...The ring should...
thingiverse
http://www.thingiverse.com/apps/customizer/run?thing_id=739573 Instructions Using the following options: outlineextruder = extruder1 line5 = line4 = line3 = line2 = line1 = ZM border_thickness = 3.6 bar_length_trim = 0 borderextruder = extruder1...
sketchfab
Used deformers to make an interwoven set of tubes into a realistic microphone wire-mesh.
grabcad
My favorite ZALMAN Cooler for LGA 775, Socket 754/939/940, Socket AM2.All measurements taken from real model with a ruler and a Vernier calipers :) (I hope this is the correct translation :)) Lowest accuracy with thermal tubes, highest - at the...
thingiverse
Just my design of leg for replacement broken one. ...I made it for Zalman ZM-K400G keyboard. ...It works fine.
thingiverse
hdd caddy for zalman R1 case (and probably other zalman cases) Will suit 3.5" or 2.5" with base mounting holes. ... HDD's can be mounted rear or forward facing.
thingiverse
Designed for Zalman Z9. ... This model copies everything except the inner hole, it is matched to the M3.5 screw.
thingiverse
Designed for Zalman Z3+ but could work with other cases. ... I only designed the right plastic bit as using one of those for each side work fine.
pinshape
If you ever lost or break leg (stand ) for your zalman z3 computer case. Here is new replacment. ...Also it may be used to tweak colours of your PC
grabcad
Zalman 120mm computer case fan Each model is modeled in 3D with the part in hand and a caliper I try to do my best to be within a 0.005'' (.1mm) tolerance.
cults3d
Modifications to ZM-02-150: 3mm Corner radii 2 x Dovetail mounting points 3 x Slots for mirror cell supports 3 x 4mm holes in secondary support Shown with ZM-02-150mm Primary Mirror Cell Assembly
thingiverse
LGA 115x bracket for old Zalman Orb cooler(unknown model) with Screw-type mounts. M3x0.5 nuts and screws are used. Designed in Kompas-3D software, for those who use it .m3d files are attached. ...There's two versions, first one is kinda beefy and second...
thingiverse
for zeiss planar zm or biogon 35. minimal finder blockage, nice protection for the lens. ...not so small but hey its good
thingiverse
This is based off the 6x6 ZM floor already up on the site. this is 1 mm thinner and should have a better mesh. ... takes me 2.5hrs from 4.5hrs using this version.
thingiverse
One of the clips for the side-walls of my Zalman X3 PC Case broke, so the side wall was not fully clipping into the case anymore. I recommend printing with a smaller nozzle, as 0.4 mm will not print the pins on the side small enough. I used a 0.2 mm...
thingiverse
May fit other Zalman cases but I am not sure (Most likely fit the normal Z11). The ventilation at the bottom of the case can benefit from these replacement feet as they raise the height of the tower to bring it away from the floor. This is especially...
thingiverse
My Nas failed a few days ago so I was forced to tinker something else together and my old Zalman Case is a goodish replacemant for a diy NAS. One Problem... lost all Drive mount Screws and vibration thingis and I don´t think it is a good solution for...
thingiverse
Made to fit a Zalman FANMATE-2 Fan speed controller. After building an enclosure for my printer, I decided to include a filter that pushes air through both a carbon sheet and HEPA filter. To do this, I purchased a 120mm fan with a a 200 cfm...
cults3d
... in progress, intended to be used as core and wrapped in carbon fibre. ...Frame to be used with https://search.ipaustralia.gov.au/designs/search/details/201910056?s=6683f7d7-1b2c-4394-8d8d-0852d30c2489 Shown with ZM-02-150mm Primary in rough position.
thingiverse
The ZM tiles Eberleg created are the perfect depth and length for the TableWar line of display trays. I just cut the width a bit to fit and added some circular holes for the bases. Looks wonderful! ...I think they would make perfect base toppers too.