zero offset 3d models
41257 3d models found related to zero offset.thingiverse
... from Hazeyall77. ...to use in conjunction with my redesigned Side Blower duct ring. You can print in PLA+ as Ive had zero issues with it warping. PETG and ABS are solid options also. You will need the Zero Offset gantry block to connect this to.
thingiverse
This is a remake of the E3d V6 zero offset mount by USWaterRockets. I found the original mount a bit overcomplicated and noticed that it doesn't hold the hotend very tightly. Therefor I made this version which basically is a direct replacement. It...
thingiverse
Simple straight front bumper mount for SCX24 C10 I designed this because I mounted my body higher to create more clearance with the tires, but flipping the stock bumper bracket put it too high, so I designed this zero offset bracket to create more...
thingiverse
... setting it aside. This is also useful for cleaning the nozzle or doing maintenance on the hot and. When you want to use the part cooling fan again, you can snap it back on. Here's a short video clip of the Zero Offset E3Dv6 Hot End Mount in action
thingiverse
That's why I'm designing a zero xy offset BLTouch mount. After several attempts i found out that the print should be sliced sideways, and not with the flat part down for better strength. The opposite will make your printed part fail between the...
thingiverse
This is a clamp without the fan mount for USWaterRockets Monoprice Select Mini E3Dv6 Zero Offset Mount: http://www.thingiverse.com/thing:1848402 Print Settings Printer: MP Mini Rafts: No Supports: No Infill: 100% Notes: Print in ABS
thingiverse
This is a a bl-touch mount made to pair zero offset E3D V6 designs [i.e](https://www.thingiverse.com/thing:2353376). It includes guiding pathways for the cables, as well support for zipties for cable management around the extruder. The by-design...
thingiverse
I tried printing the Zero Offset mount for my MPSM but for some reason the holes for the heat sink clamp were too small and it wasn't even close to fitting with ether the stock V5 clone heatsink or the genuine V6 heatsink. So I modified the STL...
thingiverse
I currently use a fan/cooler holder like this: http://www.thingiverse.com/thing:839620 I am including a reference to the Hackaday article for background...
thingiverse
This is a zero offset adapter for an E3D hot end clone found here.(https://www.amazon.com/gp/product/B077NZR8NZ/ref=oh_aui_detailpage_o01_s00?ie=UTF8&psc=1) I wanted to use the existing hot end carriage because it is steel, and would hold up to the...
prusaprinters
This is a replacement backplate for the Creality Ender 3 S1/S1 Pro Sprite Extruder that moves the CR Touch probe inline with the nozzle on the Y axis producing a zero probe offset. Many people are having issues with automatic bed leveling on...
thingiverse
this is a remix of these three items, so thanks to the designers of those the dual fan - https://www.thingiverse.com/thing:2722203 the zero offset mount - https://www.thingiverse.com/thing:3126327 the fan adapter -...
thingiverse
It is specifically designed to have zero (or close to zero) Y offset from the nozzle (read below for explanation). On my printer the offsets ended up being X=40, Y=0, Z=-2.02, though this should be measured per installation. ...Printed in Overture PLA,...
thingiverse
Designed this for the Zero Offset Bracket for the MPSM. It's still a WIP, the plan is to make it have a 50mm radial fan on the side for parts cooling. I just have to wait until I order said fan. For now it's just a 40mm Noctua fan mount. I've...
thingiverse
Absolutely zero offset from the original mount, and since i used the original heater cartridge and thermistor, it works without any additional modification. ...The nozzle does sit a about 3-5mm higher than the original, but easily within the range of...
thingiverse
I modified the zero offset mount for square nuts as my printer didn't have regular hex shaped ones. it will still work with hex nuts but you'll need to hold them in place while tightening! at first I modified the stock cooling to better clip in...
thingiverse
It is specifically designed to have zero (or close to zero) Y offset from the nozzle (read below for explanation). On my printer the offsets ended up being X=40, Y=0, Z=-2.02, though this should be measured per installation. ...Printed in Overture PLA,...
thingiverse
Zero Y offset 3D-Touch mount for Creality Sprite -------------------------------------------- When testing the UBL, it was found that the difference between the probe readings and the actual nozzle height increases as the head moves from the left...
thingiverse
IMPORTANT: Make sure you use AzzA's Z extensions so that the extruder motor does not hit the top brace. (https://www.thingiverse.com/thing:1444979) remixed using the best parts of CarstenD's and Evaken's E3D Mounts for the Wanhao Duplicator i3...
thingiverse
Adjusted to fit different fan shrouds and made it little bit bigger as I was unable to fit the hotend (the mount bottom wall was pushing hotend) You can see the photos of it near the original one
thingiverse
Remixed the fan shroud from https://www.thingiverse.com/thing:3782121 for a 40x10mm fan instead of 40x20 to save some space.
thingiverse
The existing Festool protector guards allow for sanding up to objects greater than approximately 12mm in height. I often encounter situations where it would be useful to use the guard to sand up to lower items like window trim or the inside of...
thingiverse
I had already purchased a [Noctua NF-A4x20 FLX 40mm x 20mm fan](https://amzn.to/2uuiiSX) before upgrading to the E3D V6. I couldn't find a bracket that allowed for both a 40mm fan and a part fan, so I tweaked this one. I used the 30mm fan that came...
cults3d
Adjusted to fit different fan shrouds and made it little bit bigger as I was unable to fit the hotend (the mount bottom wall was pushing hotend) You can see the photos of it near the original one
prusaprinters
This adds a similar to stock fanguard, with a little extra reinforcement also to keep the arm for the CR Touch from bending. As with the original:x_offset: -46.8y_offset: 0You will need two M3 nuts to attach the CR touch. ...Still no supports...
thingiverse
Instructions The spacer is designed to sit on the 5mm thick vertical perspex plate which activates the Z-axis zero microswitch, tripping it 3mm (the thickness of the glass) earlier than it would without. When you put the glass plate on, just use...
thingiverse
Ender 3 S1 Duct Fan upgrade with (4020) with Zero Y offset plate. ... X offset is -46mm Y Zero offset!
thingiverse
I also modified the sensor mount so you can mount a CR Touch sensor, and modified the location so that there is no offset between the sensor and the nozzle in the Y axis to improve accuracy and eliminate any probing errors due to twists in the X...
myminifactory
More will come, but in short the back mount is a remix and the rest is my own. The files need to be reoriented for printing on your printer.