zigbee 3d models

Mit dieser Halterung kann man denn Motion Sensor von Lidl gut auf seine Bedürfnisse einstellen. Wenn Ihnen das Ding gefällt, würde es mich mit einer kleinen Spende von etwa 50 Cent oder mehr motivieren, mehr Zeit für andere Upgrades aufzuwenden. ...

I'm a beginner in making models with Fusion360.I share the f360 files so you can remix them! I made two models one 30 degrees and one 90 degrees angle. ...You can place them on you're desk or place them on you're wall / ceiling with sticky tape.Happy...

Same as the original model, but instead of the big logo-hole, it has neat ventilation stripes.

Page of project: https://sprut.ai/client/projects/105 ----------------------------------------------------------------------------- Project page: https://sprut.ai/client/projects/105

I designed this for a friend concerned curtain motor controller.The lid is easy to click on the cabinet.The switching unit can also be clicked into place.It is made for 2 adhesive tubes 10x15mm, One to the motor and one to the socket.This design was...

Remastered from a concept originally designed by Pb84, this iteration enables secure wall installation, eliminating the need for screws. ...Additionally, reinforced tree-like supports have been integrated to enhance the printing process.

Used to mount a ThirdReality motion sensor in a corner.https://www.amazon.com/dp/B09MVKWBFF?

A box for a 2 channel relay for Home Automation. Print in Yellow or light color if you want to see LED under the cover. The box in screwless. You might put some screw to fix on a wall. Un boîtier pour une carte à deux relais pour projet...

Tired of having to change the puny coin cell battery so much?  Well go big or go home!With this case and a tiny bit of soldering you can now wait much, much longer to swap batteries!Takes just over an hour to print.  No supports. ... I just used PLA and...

<p>I wanted to mount my Sonoff USB 3.0 Dongle away from my Home Assistant hardware. The hardware is located in my utility closet, that had a lot of 16 mm electricity pipes. ...So designed a clip for the dongle so I can attach it to one of those...

Created to house the Aqara sensors I'm using for my automatic car gate. ...I recommend using silicone sealant to provide additional waterproofing.

This is a spool holder that lets you keep the door on your FlashForge Adventurer 3 without making any modifications to the machine for printing external filament. All of the other designs are hours and hours, tons of wasted plastic and you have to...

I tweaked Akovacs' design, which I really admired, to accommodate my modded CC2531. ...I incorporated a SMA PCB edge connector as described on Hackaday (https://hackaday.io/project/163505/gallery#f1a71f708136a1ce1e18202a1ef22e30).

Модификация корпуса https://www.thingiverse.com/thing:4161582 пульта на основе платы от Jager. Основная статья тут https://modkam.ru/?p=1264. Позволяет использовать батареи AAA. Только нижняя часть. Остальное по оригинальной ссылке автора. Также...

Remix of Jujumo's wallmount. ...I added holes for screws and made the bottom thicker a little bit thicker for better support of the screws.

This replacement case allows the Sonoff SNBN-02 to be use on a water pipe to measure the surface temperature of the pipe. I use this to monitor the performance of my central heating system. I have compared the Sonoff with analogue pipe...

As these sensors use batteries, I wanted a mount where I can remove the sensor, replace battery and mount it again without the need to replace the double sided tape.This collection includes the following mounts for:SNZB-03 PIR sensorSNZB-04 Door...

I printed it in pla.The remote can be easely remvoed for battery change.No support is needed.

A very simple mount/holder for a Tuya PIR Motion Sensor. ... Lets you place the sensor on its side without rolling away.

I designed this friction-fit case for the AVR RZUSBstick to be as minimal as possible, but added the option to include a killerbee wasp emblem for those who flash the killerbee firmware. The design includes a plain case and one with a wasp emblem...

Print this Model without any supports and with a layer height of .2 mm and 90% infill.You may need to heat up the cap after printing to make it conform better around the USB-A connector so it won't fall off.To close up the enclosure use superglue or...

<p>This mount can be used if you want to mount the USB stick somewhere not directly in the USB port (which is very much recommended due to interference). ...It has two small wholes in the back for screws but I just taped it to the wall.</p><p>It holds...

<p>Corner and flat mounts for Aqara sensors - The corners are overly large as to cover / match the anchors of existing sensor mounts I had.</p> <h3>Print instructions</h3><p>Prints without supports. ...Each type requires a sensor 'cup' to be printed...

The blank case was taken directly from https://www.thingiverse.com/thing:3502399, with a simple addition of 6mm to its length. ...This modification accommodates the slightly longer CC2531 module, which requires an additional 6mm to properly position its...

This design is heavily inspired by this [earlier design](https://www.thingiverse.com/thing:3532598), except that it comes with antenna support. ### Design notes * I decided not to design grilles to avoid having dust entering the case. * Also...

Smart Home Pro: Upgrade Your Space with the Xiaomi Aqara Switch