zohd hatch 3d models
5436 3d models found related to zohd hatch.
thingiverse
ZOHD's Compact Nano Talon Tail Control Horn Assembly.
thingiverse
ZOHD Alpha Strike Battery Plate Replacement. ...Printed using PETG.
thingiverse
ZOHD Dart250 - F411 with full support and stack enabled
thingiverse
... to hold it in place. Mostly intended to be used with DJI fpv units, or caddx vistas, that aren't able to be mounted in the wing. Be sure to mount it about 1cm forward of where is it pictured or you'll need to cut a small amount of foam on the hatch.
thingiverse
I found this https://www.thingiverse.com/thing:3605567 and wanted to use it, but it flopped around so I made this little bar to attach to my GT2 talon (Zohd). Still have to fine tune where the two design meet. busy printing now. IT fits on the...
cults3d
Modified the Cam holder and the AirUnit Mount for the ZOHD Dart XL
thingiverse
ZOHD Dart XL FC holder. ...The main spar is supposed to hold it in place.
thingiverse
Hawkeye Firefly 4K Split cam mount for Zohd Talon GT Rebel
thingiverse
Complete setup of a banked wing aircraft engine Zohd Dart 600.
thingiverse
Modified the Cam holder and the AirUnit Mount for the ZOHD Dart XL
thingiverse
Print it used to install the 19mm camera into ZOHD 250g plane. ... enjoy
thingiverse
Human: Install the buzzer on the left side of the Zohd GT Rebel's wing.
thingiverse
ESC mount for the stock 40 amp ZOHD ESC https://youtu.be/36a_YmIp3Zk
thingiverse
Zohd XL Motor Mount With Prop Saver This is an upgrade for Zohd XL FPV Wing to replace the weak wooden motor mount. ... It will also save the prop from getting damaged by touching the ground when landing.
thingiverse
Nano cam cover for the ZOHD Dart 250g. ... The Runcam Phoenix 2 gets hot, so I added air ventilation holes.
thingiverse
A compact battery compartment for the popular ZOHD Dart XL drone is now available, offering users greater convenience and portability.
thingiverse
Zohd Dart XL DJI Cam mount. ... Holds the DJI cam without screws, but can be used if necessary.
thingiverse
A canopy for ZOHD Drift which can carry DJI FPV System lite (Vista/Nebula/Pro) Print with PETG or another heat resistance filament. ...
thingiverse
This is a mount for the Insta360 Go2 for the ZOHD Dart 250G. ...It's like a saddle for the Wing
thingiverse
Mount for nano sized cameras for the ZOHD Dart250. Friction fit to the fuselage. Needs to be rotated slightly to fit the printbed. ...
thingiverse
A super lightweight (less than 1g) adapter to snugly fit a RunCam Split 3 Nano in the nose of a ZOHD Drift.
thingiverse
ZOHD Drift parts: Canopy; printed with LW-PLA DJI Camera mount; printed with TPU Vista, GPS, antenna mount; printed with TPU
thingiverse
Remix of ZOHD Dart 250 Nano Cam Mount by Eondar to remove the camera altogether and just have a nose plug.
thingiverse
Print the ZOHD Drift M3 Wing Thumbscrew in a neon color that stands out, ensuring it's never lost in the shuffle.
thingiverse
This is a slice of a flat hatch from thingiverse (most of it is under the virtual Print table) and an own upscaled stl just place inside the other for gcode...
thingiverse
Replacing the Bottom Hatch With a GoPro Session Action Cam
thingiverse
This Design is inspired from Painless360s Antenna Mount, Name "ZOHD Dart 250G Antenna Support", ID 4726331. As Painless 4mm Antenna Mount don't allow remixes, it's completely self designed for a Caddx Vista Antenna with 3mm Dia. ...