zte speed 3d models
49745 3d models found related to zte speed.thingiverse
Remix of this thing with holes for Actobotics instead of Tetrix: http://www.thingiverse.com/thing:801099 Mounts a ZTE Speed to an Actobotics channel, for the upcoming FTC season. Features: Prints without support. Compact on the Actobotics...
thingiverse
... without support on Ekocycle printer. Mounts with 4 standard Tetrix screws and nuts. Feed the rubber band through first without the ZTE Speed in place. Then slide the ZTE Speed in and pull the rubber band over the top as shown in the photo.
thingiverse
This part is designed to hold a ZTE speed phone on a tetrix robot.
grabcad
This is one of the phones allowed to use during the FTC 2015-2016 season. This model is reasonably accurate (all dimensions +/- 0.5mm) and it was created by Tilman G, member of 6964 FTC Team Igutech. Everyone is free to modify, print, share, do...
thingiverse
This model is based off of the Tetrix ZTE Speed mount, for our needs we needed a stronger version so I modeled a thicker version. The base is thicker and the support column is thicker by .1 inches. Hole pattern is the same. ...UPDATE: Still had the...
thingiverse
This is a mount for the ZTE Speed for use on FTC robots. This design incorporates a USB Strain reliever, which is a hole for the USB cable that uses no zip ties. The mount comes in 2 pieces to save on material and for those who have smaller printers....
thingiverse
This is a ZTE Speed phone mount designed for FTC robots. The phone mounts vertically, allowing the camera to be used easily with full access to the screen. Phone is held in by friction to avoid the use of extra parts, and also has a USB protector to...
thingiverse
This case is designed to hold the ZTE Speed Smartphone in a way that does not block it's camera, while also holding the Micro-USB in firmly. It also has a Tetrix hole pattern on the back for easy attachment to any Tetrix parts. The front of the case...
thingiverse
These models are protective cases for the Modern Robotics controllers and ZTE Speed smartphone used in the FIRST Tech Challenge. Made by Team 4029, 2 Bits and a Byte, these cases reinforce the PowerPole and miniUSB connectors to ensure that wires do...
thingiverse
Ziptie this mount to the USB micro connector that goes into the ZTE phone, as shown with the zipties in the pictures. For removable installation: wrap a rubber band around the phone and over the slots on the mount, as shown in the pictures. This...
thingiverse
Mount for the new FTC hardware on tetrix. Nota Bene: The side of the phone with the camera is very slightly thicker than the bottom of the phone. ...It will sit more snugly in the mount, but you should not have an issue.
thingiverse
ZTE Speed Phone Mount created by Trojan Robotics for the new 2015-2016 Controls. Easy snap in place. Middle hole and outer holes work with Tetrix Pattern, while the other holes work with the Actobotics Pattern. Print 2 of the same. Middle support is...
thingiverse
This dual phone holder is meant to keep paired phones together when charging for organizational purposes. This is especially helpful when your FTC team has more than 2 pairs of phones to keep track of, and this will ensure that paired phones stay...
thingiverse
Based on this design, but modified to be printed in two parts that screw together (screw heads fitting into a V-shaped groove needed to avoid having an unprintable overhang).Printed and slightly tested so far. More tweaks may come ...
thingiverse
I wanted to create my own phone holder case, and I incorporated all the things I wanted in one. Including a way to turn off the phone without the risk of something else doing it, and having mounting holes on two sides. I also wanted a secure way to...
thingiverse
We were having many "cant find USB device" error messages that seemed to be related to the USB plug connection wiggling. The mount "2" can be mounted to the bottom or on the back using the standard tetrix button head screws. Mount "1" has a bottom...
thingiverse
This mount is made to hold a ZTE Speed Phone for use with Tetrix in an FTC design competition.
thingiverse
A phone case for the ZTE Speed for FTC made by FTC team 4081 Print Settings Rafts: Doesn't Matter Supports: Yes
thingiverse
This Y-Not Robots² 6780 base will mount to existing Tetrix channel hole patterns, and is made to fit the ZTE Speed phone for the upcoming FTC season. Mate with the matching cover (http://www.thingiverse.com/thing:999616) for a secure option of...
thingiverse
This Y-Not Robots 4224 base will mount to existing Tetrix channel hole patterns, and is made to fit the ZTE Speed phone for the upcoming FTC season. Mate with the matching cover (http://www.thingiverse.com/thing:999616) for a secure option of...
thingiverse
Customized version of http://www.thingiverse.com/thing:1665478 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=1665478 Instructions Using the following options:...
thingiverse
This is a mount that connects a ZTE Speed Phone (probably works for others) to a Logitech F310 gamepad (probably works for others). It has spaces for wires to be wrapped around and a Monoprice 4-Port USB 2.0 HUB to be fitted into place. This was made...
thingiverse
Simple holder for ZTE MC801A 5g modem. ...Print upside down with supports.
thingiverse
case fo zte blade a1 Print Settings Printer: prusa i3 Rafts: No Supports: No Resolution: 0.1
thingiverse
A phonemount to a (bigger) tripod. ... Phone: ZTE a452 Tripod: ROWI 6085 VF You're free to make it fit to other phones/tripods.