Alien Queen 3D Printing Figurine in Diorama | Assembly

Alien Queen 3D Printing Figurine in Diorama | Assembly

gambody

ABOUT THIS 3D FIGURINEAlien Queen surrounded by inexhaustible Xenomorphs in diorama with Darth Vader is a reflection on what the possible clash of two fictional universes would look like. The author of this majestic diorama for 3D printing was drawing inspiration from amazing illustrations by talented artist Guillem H. Pongiluppi who created a great series of concept arts featuring Darth Vader and a bunch of Stormtroopers fighting off a horde of Xenomorphs from the Alien franchise. As indicated the author of the initial concept, the whole battle takes place in the remote planet LV-426 where Stormtroopers of the elite 501st Legion are fighting against the Space Cockroaches. The brave soldiers are stronger than ever though seem to be losing the battle against tireless Xenomorphs when the dark lord Sith Darth Vader arrives and evacuates the men of the Legion. At that very moment, the mother of every Drone and Warrior in the hive arrives. Sounds incredible, doesn’t it? The author of the 3D printing diorama spent 240 hours in total to convey the atmosphere of the confrontation - Alien Warriors led by their Queen are depicted crawling out of holes, preparing for the attack. Alien Queen, in her turn, is displayed advancing with her whole body towering above everyone else and clearly ready to rush into action. Dark Lord of the Sith is ready to confront the beast single-handed but the outcome of the battle is open to question. The whole mood of the diorama proves that a possible crossover between Alien and Star Wars franchises would be clearly a creepy incident but who would mind seeing a movie like this! And while these are only concepts and we are yet to see what's there in store for both franchises the incredible diorama is already available to be 3D printed and placed on your display shelf. Go order the STL files and get down to the unique project!ADAPTATION FOR 3D PRINTINGAlien Queen figurine in diorama with Darth Vader and crawling Xenomorphs for 3D printing is a static assembly model and its moderation and adaptation for different types of 3D printers took Gambody team 88 hours in total. With the whole diorama being comprised of the great Alien Queen, Darth Vader figurine and 10 smaller Xenomorphs, Gambody team dedicated much time and effort to review every single part of the impressive scene and to make sure every element of the diorama is adapted for 3D printing. The model’s cutting in its huge assembly version was chosen by our team to minimise the amount of filament needed for generated support. Therefore, and also so to ensure the cleanest 3D printed result possible, each dorsal tube on each Xenomorph’s back, each creature’s head, tail and all extremities are provided as a separate assembly piece. If you take a look at the way the Queen herself is cut into assembly parts, you will see that with the same purpose of guaranteeing the clean outcome, the figurine was divided into many separate parts along the creature’s body seams and its jaws, as well as inner jaw, were extracted from the monster’s mouth for convenient printing. Consequently, Darth Vader figurine comes with the cloak “taken off” and the lightsaber separate. Besides, some of the diorama’s parts were hollowed out for you to save resin in the model’s Eco version. All assembly parts are provided in STL files in recommended positions that were worked out so to ensure the smoothness of the details’ surfaces after printing and that the 3D printing beginners won't face difficulties when placing the parts on a build plate. The figurine is saved in STL files, a format supported by most 3D printers. All STL files for 3D printing have been checked in Netfabb and no errors were shown.The model's scale was calculated from Alien Queen's actual height that is 6096 mm. The 3D printing figurine's chosen scale is 1/16 for the FFF/FDM version and 1/32 for the DLP/SLA/SLS versions.VERSIONS' SPECIFICATIONSFFF/FDM 1.0 version features:- Contains 146 parts;- A printed model is 332 mm tall, 302 mm wide, 536 mm deep;- Assembly kit includes locks to connect the model's parts securely without glue. One lock 145_ge_lock_7S(x7)​ needs to be printed 7 times; lock 146_ge_lock_10H(x61) needs to be printed 61 times;- Instead of Darth Vader, your Queen may confront the 1:16 scale versions of Ellen Ripley, Power Loader or Predator;- All parts are thoroughly divided in such a way that you will print them with the smallest number of support structures.DLP/SLA/SLS 1.0 version features:- Contains 35 parts;- A printed model is 166 mm tall, 151 mm wide, 268 mm deep;- All parts are divided in such a way to fit the build plates and to make sure that support structures are generated where needed.DLP/SLA/SLS Eco 1.0 version features:- Contains 35 parts;- A printed model is 166 mm tall, 151 mm wide, 268 mm deep;- Contains some hollowed out parts to save resin.WHAT WILL YOU GET AFTER PURCHASE?- STL files of Alien Queen Figurine in Diorama for 3D printing which consist of 216 parts;- 3 versions of files for this model for FFF/FDM, DLP/SLA, DLP/SLA Eco and SLS;- High-poly detailed figurine of Alien Queen;- Detailed settings that we provide as a recommendation for Cura , Simplify3D and Slic3r for the best print;- Full technical support from the Gambody Support Team.You can get the figurine of Alien Queen​ in Diorama for 3D Printing immediately after the purchase! Just click the green Buy button in the top-right corner of the model’s page. You can pay with PayPal or your credit card.Watch the tutorial on how to assemble Alien Queen 3D Printing Figurine in Diorama at Gambody YouTube channel.Also, you may like other Alien vs Predator 3D Printing Models as well as another Darth Vader 3D Printing Figurine._______FAQ: Where can I print a model if I have no printer?How to get started with 3D printing?How to set up my 3D printer?How to choose right 3D model print bed positioning? How to paint printed figurine?Below you can find printing recommendations for Cura, Simplify3D and Slic3r software.These are basic settings that were tested in Cura 4.8.0 slicer. The test models were printed on Ultimaker 2, Creality Ender 3, Creality CR-10S Pro V2, Anycubic I3 Mega, Anycubic I3 MegaS 3D printers with PLA and PETG filaments.Disclaimer: The following printing settings are a recommendation, not an obligation. The parameters can vary depending on the peculiarities of your 3D printer, the material you use and especially the particular assembly part at hand. Each part that any model comprises often needs preliminary review and you are free to tweak the settings the way you find suitable.Note:- You can scale up the model (downscaling is not recommended!);- All connectors should be printed at 100% Infill;- For all parts of locks (“ge_lock” in “Source files”) you need to change "Brim" type to "Skirt" in Build Plate Adhesion section.QualityLayer Height: 0.12 mm (you can also set Layer Height at 0.16 or 0.2mm for 0.4mm nozzles)Initial Layer Height: 0.2 mm (carefully level the print bed and keep your Initial Layer Height the same as the main Layer Height)Line Width: 0.4 mmWall Line Width: 0.4 mmOuter Wall Line Width: 0.4 mmInner Wall(s) Line Width: 0.4 mmTop/Bottom Line Width: 0.4 mmInfill Line Width: 0.4 mmSkirt/Brim Line Width: 0.4 mmSupport Line Width: 0.4 mmInitial Layer Line Width: 100%Shell Wall Thickness: 0.8 mmWall Line Count: 2Outer Wall Wipe Distance: 0.3 mmTop Surface Skin Layers: 0Top/Bottom Thickness: 0.6 mmTop Thickness: 0.6 mmTop Layers: 5Bottom Thickness: 0.6 mmBottom Layers: 5Initial Bottom Layers: 5Top/Bottom Pattern: LinesBottom Pattern Initial Layer: LinesTop/Bottom Line Directions: [ ]Outer Wall Inset: 0 mmOptimize Wall Printing Order: CheckCompensate Wall Overlaps: CheckCompensate Inner Wall Overlaps: CheckMinimum Wall Flow: 0%Fill Gaps Between Walls: EverywhereFilter Out Tiny Gaps: CheckHorizontal Expansion: 0 mmInitial Layer Horizontal Expansion: 0 mmHole horizontal expansion: 0Z Seam Alignment: User SpecifiedZ Seam Position: BackZ Seam X: Average length of your printer’s plate (e.g.”150” if your plate is 300mm on the X-axis)Z Seam Y: A value higher than the length of your plate on the Y-axis (e.g. 700)Seam Corner Preference: Hide SeamExtra Skin Wall Count: 1Skin Overlap Percentage: 10%Skin Overlap 0.04 mmInfill Infill Density: 20% (for all smaller parts and for all parts of connectors use 100% Infill)Infill Pattern: TrianglesConnect Infill Lines: CheckInfill Line Directions: [ ]Infill X Offset: 0 mmInfill Y Offset: 0 mmInfill Line Multiplier: 1Extra Infill Wall Count: 0Infill Overlap Percentage: 10-20%Infill Overlap: 0.04 mmSkin Overlap Percentage: 5%Skin Overlap: 0.02 mmInfill Wipe Distance: 0 mmInfill Layer Thickness: 0.24 mmGradual Infill Steps: 0Infill Before Walls: CheckMinimum Infill Area: 0 mm2Skin Removal Width: 0.8 mmTop Skin Removal Width: 0.8 mmBottom Skin Removal Width: 0.8 mmSkin Expand Distance: 0.8Top Skin Expand Distance: 0.8Bottom Skin Expand Distance: 0.8Maximum Skin Angle for Expansion: 90˚Minimum Skin Width for Expansion: 0.0Skin Edge Support Thickness: 0Skin Edge Support Layers: 0Material Initial Layer Flow: 100%Printing Temperature: See your filament settingsInitial Printing Temperature: Your filament settingsFinal Printing Temperature: Your filament settingsBuild Plate Temperature: Your filament settingsBuild Plate Temperature Initial Layer: Your filament settings + 5°Flow: 100% (Important! If you face difficulty printing the model, you may need to adjust the Flow parameter. You may research the topic using the Internet or seek assistance at our Customer Support Team at support@gambody.com)Speed You can increase the printing Speed by 20% when you print simple objects. For small/thin parts you need to decrease the Speed by 25% - 50%.Print Speed: 50 mm/s    Infill Speed: 50 mm/s    Wall Speed: 25 mm/s          Outer Wall Speed:25 mm/s          Inner Wall Speed: 50 mm/sTop/Bottom Speed: 25mm/sSupport Speed: 25 mm/s           Support Infill Speed: 45 mm/s          Support Interface Speed: 25 mm/s                Support Roof Speed: 25 mm/s                Support Floor Speed: 25 mm/sTravel Speed: 80 mm/sInitial Layer Speed: 80 mm/sInitial Layer Print Speed: 20 mm/sInitial Layer Travel Speed: 80 mm/sSkirt/Brim Speed: 20 mm/sZ  Hop Speed: 5 mm/sNumber of Slower Layers: 2Enable Acceleration Control: CheckWhen printing simple objects, you need to set all Acceleration parameters at 500 mm/s. For small/thin parts you need to decrease the Acceleration by 50% - 70%.Travel Enable Retraction: CheckRetraction Distance: 4-8 mm, 1-3 mm for Direct Extruder (This is the most important retraction parameter. You can find your optimal value of Retraction Distance by printing any test object, e.g. bridges, towers etc.)Retraction Speed: 25mm/sRetraction Retract Speed: 25 mm/sRetraction Prime Speed: 25 mm/sRetraction Extra Prime Amount: 0 mm3 Retraction Minimum Travel: 1.5 mmMaximum Retraction Count: 100Minimum Extrusion Distance Window: 6,5 - 10 mmLimit Support Retractions: CheckCombing Mode: AllMax Comb Distance With No Retract: 30 mmRetract Before Outer Wall: CheckAvoid Printed Parts When Travelling: CheckAvoid Supports When Travelling: CheckTravel Avoid Distance: 1 mmLayer Start X: 0.0 mmLayer Start Y: 0.0 mmZ Hop When Retracted: CheckZ Hop Height: 0,3 mmCooling Enable Print Cooling: CheckFan Speed: 100%Regular Fan Speed: 100%Maximum Fan Speed: 100% Regular/Maximum Fan Speed Threshold: 10 sInitial Fan Speed: 0%Regular Fan Speed at Height: 0.36 mmRegular Fan Speed at Layer: 3 Minimum Layer Time: 10 sMinimum Speed: 10 mm/sSupport Generate Support: CheckSupport Structure: Normal (you can try using Tree Support Structure if you have difficulty printing any particular assembly part)Support Placement: Everywhere Support Overhang Angle: 60° (this parameter can range from 30° to 70° depending on the part at hand)Support Pattern: Zig ZagSupport Wall Line Count: 1 (stronger support that might be more difficult to remove) 0 (less strong support but is easier to remove)Support Density: 15%Support Line Distance: 2.6667 mmInitial layer support line distance: 2.667 mmSupport Z Distance: 0.12 mmSupport Top Distance: 0.12 mmSupport Bottom Distance: 0.12 mmSupport X/Y Distance: 0.8-1 mmSupport Distance Priority: Z overrides X/YSupport Stair Step Height: 0.3 mmSupport Stair Step Maximum Width: 5.0 mmSupport Stair Step Minimum Slope Angle: 10°Support Join Distance: 2.0 mmSupport Horizontal Expansion: 0.2 mmSupport Infill Layer Thickness: 0.2 mmGradual Support Infill Steps: 0Minimum Support Area: 2 mmEnable Support Interface: Check (generates additional “pillow” on the support structure that leads to a more even surface, but can be difficult to remove in hard-to-reach areas)Enable Support Roof: CheckEnable Support Floor: CheckSupport Interface Thickness: 0.8 mmSupport Roof Thickness: 0.8 mmSupport Floor Thickness: 0.8 mmSupport Interface Resolution 0.2 mmSupport Interface Density: 50-100%        Support Roof Density: 50-100%Support Roof Line Distance: 0.8 mm        Support Floor Density: 50-100%Support Floor line Distance:  0.4mmSupport Interface Pattern: Grid Support Roof Pattern: Grid (this parameter should differ from Bottom Pattern Initial Layer in “Shell” section)Support Floor Pattern: GridMinimum Support Interface Area: 10mmMinimum Support Roof Area: 10 mmMinimum Support Floor Area: 10 mmSupport Interface Horizontal Expansion: 0.0 mmSupport Roof Horizontal Expansion: 0.0 mmSupport Floor Horizontal Expansion: 0.0 mmFan Speed Override: CheckSupported Skin Fan Speed: 100%Use Towers: CheckTower Diameter: 4 mmMinimum Diameter: 3.0 mmTower Roof Angle: 65° Build Plate Adhesion Build Plate Adhesion Type: Skirt/Brim (For unsteady parts, and those parts that may come unstuck use “Brim”. For bigger assembly parts that have large adhesion area and for all parts of locks and claws that you want to come out clean use "Skirt")Skirt/Brim Minimum Length: 250 mmBrim Width: 8.0 mm       Brim Line Count: 10Brim Only on Outside: CheckMesh Fixes Union Overlapping Volumes: CheckMerged Meshes Overlap: 0.15 mmSpecial ModesPrint Sequence: All at OnceSurface Mode: NormalExperimentalSlicing Tolerance: MiddleMaximum Resolution: 0.01 mmFlow rate compensation max extrusion offset: 0 mmFlow rate compensation factor: 100%This model was tested with PLA material.To avoid printing problems, we recommend the following settings:ExtruderNozzle Diameter: 0.4 mmExtrusion Multiplier: 0.97Extrusion Width: AutoRetraction Distance: 5.00 mmExtra Restart Distance: 0.00 mmRetraction Vertical Lift: 0.08 mmRetraction Speed: 5400.0 mm/minWipe Distance: 5.00 mmLayerPrimary Layer Height: 0.2 mmTop Solid Layers: 8Bottom Solid Layers: 5Outline/Perimeter Shells: 2Outline Direction: Inside-OutFirst Layer Height: 90%First Layer Width: 100%First Layer Speed: 20%AdditionsUse Skirt/Brim: CheckSkirt Layers: 1Skirt Offset from Part: 6.00 mmSkirt Outlines: 5InfillInternal Fill Pattern: Fast HoneycombExternal Fill Patern: RectilinearInterior Fill Percentage: 10%Outline Overlap: 22%Infill Extrusion Width: 100%Minimum Infill Length: 5.00 mmCombine Infill Every: 1 layersExternal Infill Angle Offsets: 45/-45 degSupportGenerate Support Material: CheckSupport Infill Percentage: 15%Extra Inflation Distance: 1.00 mmSupport Base Layers: 0Combine Support Every: 1 layersDense Support Layers: 0Dense Infill Percentage: 70%Support Type: NormalSupport Pillar Resolution: 5.00 mmMax Overhang Angle: 60 degHorizontal Offset From Part: 0.50 mmUpper Vertical Separation Layers: 1Lower Vertical Separation Layers: 1Support Infill Angles: 45 degTemperatureExtruder 1 Temperature: 210Heated Bed: 60CoolingIncrease fan speed for layers below: 45.0 sec  Maximum Cooling fan speed: 50%Bridging fan speed override: 100%SpeedsDefault Printing Speed: 4800.0 mm/minOutline Underspeed: 50%Solid Infill Underspeed: 80%Support Structure Underspeed: 80%X/Y Axis Movement Speed: 10800.0 mm/minZ Axis Movemen Speed: 1002.0 mm/minAdjust printing speed for layers below: 15.0 sec   Allow speed reduction down to: 20%OtherUnsupported area threshold: 20.0 sq mLayer height  Layer height: 0.1 mm  First layer height: 90%Vertical shells  Perimeters: 2Horizontal shells  Soid layers:               Top: 8              Bottom: 5Quality  Detect thin walls: Check  Detect bridging perimeters: CheckAdvanced  Seam position: RandomInfill  Fill desity: 20%  Fill pattern: Honeycomb  Top/bottom fill pattern: RectilinearReducing printing time  Combine infill every: 1 layersAdvanced  Solid infill every: 0 layers  Fill angle: 25 deg  Solid infill threshold area: 0mmSkirt  Loops: 2  Distance from object: 6 mm  Skirt height: 1 layers  Minimum extrusion length: 4 mmBrim   Brim width: 10 mmSupport material  Generate support material: Check  Overhang threshold: 45 deg  Enforce support for the first: 3 layersRaft  Raft layers: 0 layersOptions for support material and raft  Contact Z distance: 0.1 mm  Pattern: Rectilinear  Patter spacing: 2 mm  Pattern angle: 0 deg  Interface layers: 2 layers  Interface pattern spacing: 0.2 mmSpeed for print moves  Perimeters: 60 mm/s  Small perimeters: 20 mm/s  External perimeters: 20 mm/s  Infill: 60 mm/s  Solid infill: 60 mm/s  Top solid infill: 30 mm/s  Support material: 50 mm/s  Support material interface: 100%  Bridges: 30 mm/s  Gap fill: 50 mm/sSpeed for non-print moves  Travel: 60 mm/sModifiers  First layer speed: 30 mm/sAcceleration control  Perimeters: 800 mm/s  Infill: 1500 mm/s  Bridge: 1000 mm/s  First layer: 1000 mm/s  Default: 1000 mm/sAutospeed  Max print speed: 100 mm/s  Max volumetrix speed: 0 mm/sExtrusion width  Default extrusion width: 0.42 mm  First layer: 0.42 mm  Perimeters: 0.42 mm  External perimeters: 0.42 mm  Infill: 0.42 mm  Solid infill: 0.42 mm  Top solid infill: 0.42 mm  Support material: 0.42 mmOverlap  Infill/Perimeters overlap: 20%Flow  Bridge flow ratio: 0.95Other  XY Size Compensation: 0 mm  Threds: 8  Resolution: 0 mm

Download Model from gambody

With this file you will be able to print Alien Queen 3D Printing Figurine in Diorama | Assembly with your 3D printer. Click on the button and save the file on your computer to work, edit or customize your design. You can also find more 3D designs for printers on Alien Queen 3D Printing Figurine in Diorama | Assembly.