Batman the Animated Series - Shadow of the Bat - Dice Matching Shared Action Tokens

prusaprinters

<p>Inspiration taken from: <a href="https://boardgamegeek.com/filepage/232054/btas-sotb-dice-matching-shared-action-tokens">https://boardgamegeek.com/filepage/232054/btas-sotb-dice-matching-shared-action-tokens</a></p> <p>(Basically) From the link above:</p> <p>Here are my shared dice tokens to replace the community pool of shared neon/pastel tokens. Each hero will now have their own matching set to be handed out to players to keep things visually organized- and easier to pickup too.</p> <p>Included are single extruder tokens and MMU tokens.</p> <p>Note: I was about 1/2 done printing these when I realized they just barely don't fit in the hero boards from the Kickstarter, If that's a deal-breaker, you can try scaling the tokens.</p> <p>---Single Extruder---</p> <p>Shared Tokens - Single - XXXXXX.3MF: Single extruder tokens that don't have corresponding "inset" files and a shallower (.4mm) cavity that should be usable via layer color change.</p> <p>I expect that if you plan to print them face up, you will need a .25mm nozzle to get any decent icon fidelity.</p> <p>---Multi Material--- (these tokens have a deeper 2mm cavity and should only be used with the 'inset' components)</p> <p>Shared Tokens - MMU - XXXXXX.3MF: Individual tokens in .3MF format,</p> <p>Shared Token - MMU - XXXXXX.STL / Shared Token - MMU - XXXXXX - Inset.STL: Tokens and their matched inset components split into seperate STL files</p> <p>Shared Tokens Project - YYYYYY.3MF: Preconfigured .3MF files that you can import directly into PrusSlicer for your MMU with a brim on each token and a purge block with a little extra purge for filaments 1 and 2. The .3MF files for Villains are assuming you have the extra dice, if not, you'll want to reduce each token count by half.</p> <p>These files are setup for a Mk2.5s with MMU2s, make sure you adjust your settings to match your printer.</p> <p>I printed the MMU tokens on their bottom edge at .15mm resolution, thin wall detection is a must.</p> <p>The "Bat" tokens and "Wild" tokens don't have a use but I was on a roll when making tokens from the user manual so I made them anyway. Get creative.</p> <p>The trays are part of an organizer that I will be releasing very soon, just have a little more work to do before publishing.</p> <p>Token Counts:</p> <p>Batman/Bruce Wayne: 2 - Move | 2 - Melee x2 | 2 - Ranged x2 | 2 - Defend | 2 - Defend/Melee</p> <p>Batgirl: 4 - Move | 2 - Melee x2 | 2 - Ranged | 2 - Defend</p> <p>Robin: 4 - Move | 2 - Melee | 2 - Ranged x2 | 2 - Defend</p> <p>Nightwing:4 - Move | 2 - Melee x2 | 2 - Ranged x2 | 2 - Defend</p> <p>Robin (Tim Drake): 2 - Move | 2 - Move x2 | 2 - Melee | 2 - Ranged x2 | 2 - Defend/Melee</p> <p>Renee Montoya: 2 - Move x2 | 2 - Melee | 2 - Ranged | 2 - Defend | 2 - Defend/Ranged</p> <p>Etrigan: 2 - Move | 2 - Melee x2 | 2 - Ranged x2 | 2 - Defend/Melee | 2 - Defend/Ranged</p> <p>Grey Ghost: 2 - Move | 2 - Melee | 2 - Ranged | 2 - Defend/Melee | 2 - Defend/Ranged</p> <p>Batwoman: 2 - Move | 2 - Melee | 2 - Melee x2 | 2 - Ranged | 2 - Defend/Move</p> <p>Catwoman: 4 - Move | 2 - Move x2 | 4 - Defend/Melee</p> <p>Phantasm: 2 - Move | 2 - Melee x2 | 2 - Ranged x2 | 4 - Defend</p> <p>Jim Gordon: 2 - Move | 2 - Melee | 2 - Ranged x2 | 2 - Defend | 2 - Defend/Ranged</p> <p>Harvey Bullock: 2 - Move | 2 - Melee | 2 - Ranged x2 | 2 - Defend | 2 - Defend/Melee</p> <p>Supergirl: 3 - Move x2 | 3 - Melee x2 | 3 - Ranged x2 | 3 - Defend/Melee</p> <p>Zatanna: 3 - Move | 3 - Melee | 3 - Ranged | 3 - Defend/Move</p> <p>Villains (Double if you have the extra dice pack)</p> <p>Brawler (Red/Yellow): 2 - Move | 2 - Melee | 2 - Melee x2 | 2 - Ranged | 2 - Defend</p> <p>Bruiser (Blue/White): 2 - Move | 2 - Melee | 2 - Ranged | 4 - Defend/Melee</p> <p>Assassin (Green/Black): 2 - Move | 2 - Melee | 2 - Ranged | 2 - Ranged x2 | 2 - Defend</p> <p>Wild Card (Purple/Green): 2 - Move x2 | 2 - Melee | 2 - Ranged | 2 - Defend/Melee</p> Category: Toy & Game Accessories