Black Evo Upgrade for Dagoma Ultimate and Discoeasy 200

cults3d

New black aluminium chassis for our Discoeasy 200. Robust chassis, elegant design true to the curve of our Easy. Attention all STL we were studied and adapted for the alu black profile from systeal and motedis link below in the description. The assembled disco, was assembled with black profiles from systeal. Caution: You will need to lengthen some of the original electrical wires. New supplier under negotiation on 29 04 2020 for a black profile kit for a sum of 56 euro including postage. Update of 29/04/2020 -Addition of the front and rear corners type Disco Ultimate for XL tray. For motedis and systeal profile -Detail of profile lengths(detail below) Update of 26/04/2020 -Add pdf file Disco Ultimate Black Evo assembly Update of 24/04/2020 -Addition of front and rear angles Disco Ultimate type Improvement: -The rear angle can now be removed without dropping the rear panel and will allow the 65mm profile clamping to be adjusted more easily. - For the assembly of the rear corners, you will need 2 screws m3 of 10 and assemble them with 2 foot locks. - Stiffer front corner Coming up: -Electronic card cover Finally available on 08 12 2018, all files named v2 for the new improvements: -Rear panel v2 to have the two extruders for the two-colour kit -Power connector v2 so that it can be adapted to the new rear panel -Front panel v2 so that it can be removed without dropping the front tensioner and minor dimension correction (provide 2 screws m3x10 and 2 additional nuts) -Front tensioner v2 to adapt to the front panel v2 -Rear tensioner v2 top material removal -Right and left button support for inter extruder+ -Right and left button support for inter extruder+ -Right and left button support for inter extruder+ -Right and left button support for inter extruder+ -Right and left button support for inter extruder+ -Right and left button support for inter extruder+ -Right and left button support for inter extruder+ -Right and left button support for inter extruder+ -Right and left button support for inter extruder+ -Right and left button support for inter extruder+ -Right and left button support for inter extruder+ -Right and left button support for inter extruder+ -Right and left button support for inter extruder+ -Right and left button support for inter extruder+ -Right and left button support for inter extruder+ -Right and left button support for inter extruder+ -Right and left button support for inter extruder+ -Right and left button support for inter extruder+ -Right and left button support for inter extruder+ -Right and left button support -You won't need any additional screws except the two screws and nuts mentioned above, on the other hand you absolutely need the m4 or m5 screws (for motedis profile) mentioned below because the screws go into the face and don't protrude to be able to install the extruder+ (see photo). -You will also need to replace the right feet with anti-vibration rubber pads. The goal is to raise the chassis to put the nema 17 connector down (see picture) and at the same time make the printer quieter. You can leave the triangle feet on to strengthen the angle. You will need 12 pads available there: https://fr.aliexpress.com/item/4-pcs-Nouveau-Anti-vibrations-En-Caoutchouc-Tapis-De-R-ception-Pieds-Antivibratoires-Pieds-Pour-2020/32870389415.html?spm=a2g0s.9042311.0.0.27426c37xnIZub New as of 26.09.2018: MKS TFT 35 display case NEW: STL for MOTEDIS aluminium profile available from 31.03.2018. New as of 13 04 2018: detail of the screws per element and detail of the profile measurement Detail of the evolution. -Same centre distance in X and Y, therefore compatible with all original or upgraded tables and carriages. Adjustable Y-spacing thanks to the micro oval, you can switch to IGUS without any constraint. -Front and back side no longer participate in tightening the belt thanks to the aluminium bar in the centre which are there for its. -Adjustable gantry position to be compatible with the original head or Z122 head. -Printing capacity for the z122 head: 196 in X, 203 in Y and 210 in Z -Printing capacity for the original head: 210 in X, 210 in Y and 210 in Z Good impression to all Detail of the attached documents Detail of the screws: M3 screw length M3x 6: quantity 18 length M3x 8: quantity 37 length M3x 10: quantity 14 length M3x 12: quantity 14 length M3x 14: quantity 2 length M3x 16: quantity 10 length M3x 18: quantity 13 length M3x 22: quantity 2 M3 nylstop nut: quantity 30 you'll find it all here: https://www.visseriefixations.fr/vis-a-six-pans-creux/tete-cylindrique-hexagonale-creuse/acier-8-8-noir/tchc-acier-8-8-noir-filetage-total-din-912.html Screw M4 length 20 for system profile: quantity32 M5 screw length 20 for motedis profile: quantity32 (a small hole at 4.5 may be necessary for motedis aluminium profiles, otherwise the thread will be tapped by inserting the screw). you'll find it all here: https://www.visseriefixations.fr/vis-a-six-pans-creux/tete-bombee-hexagonale-creuse/tbhc-acier-10-9-noir-iso-7380.html Detail of the aluminium profile in the classic version (210x210 top): 2 bar of 104 2 bar of 65 2 bar of 360 2 bar of 133 2 bar of 340 1 bar of 400 Detail of the aluminium profiles for XL tray (we add 6cm more on each side than the classic version) 2 bar of 164 2 bars of 125 2 bar of 360 2 bar of 133 2 bar of 340 1 bar of 520 You'll find it all here in black at systeal: https://www.systeal.com/fr/profiles-aluminium-8-mm/1467-profile-aluminium-30x30-fente-8-mm-anodise-noir.html or in grey: https://www.systeal.com/fr/profiles-aluminium-8-mm/1036-profile-aluminium-30x30-fente-8-mm.html or here at Motedis in grey: https://www.motedis.fr/shop/Profile-a-rainures/Profile-30-B-Type-rainure-8/Profile-aluminium-30x30-B-Typ-rainure-8::99999432.html 12 brackets you'll find it all here: http://www.systeal.com/fr/assemblage-fixation-8mm-profile-aluminium/920-equerre-de-fixation-interne-profiles-8-mm.html or here: on the other hand you'll need 4 like this one https://www.motedis.fr/shop/Profile-accessoires/Accessoires-30-B-Type-rainure-8/Equerre-interne-30-zamak-B-Type-rainure-8-90G::99999859.html Plus 10 more like this one: https://www.motedis.fr/shop/Profile-accessoires/Accessoires-30-B-Type-rainure-8/Equerre-interne-30-zamak-B-Type-rainure-8-90G-R::99999860.html For a shot at the 15 04 2020 in a classic version of: -96.32 euros including shipping for a black chassis at systeal -88 euros including shipping at systeal for a grey chassis -61 euros including shipping at motedis for a grey chassis New supplier under negotiation on 29 04 2020, for a black profile kit around 56 euro including port. All other parts are available at dagoma. Example: inductive sensor, 24mm motor, extruder spring, plate, gear wheel, switch, buildgrip, pneumatic connector, mks card............................................................................................................................ here: https://dagoma.fr/boutique/accessoires.html assembly videos https://www.youtube.com/watch?v=DMj0l0eccYU https://www.youtube.com/watch?v=C0HMLBC6ijY https://www.youtube.com/watch?v=_PG2a75Nr7g https://www.youtube.com/watch?v=6TPyJJJV50U The adjustable tray here: https://www.thingiverse.com/thing:2760991 The USB adapter: https://fr.aliexpress.com/item/30cm-USB-Print-Cable-USB-B-Male-to-B-Female-Wire-Socket-Printer-Panel-Mount-Extension/32809932065.html?spm=a2g0s.9042311.0.0.lPGRFY -Think about changing your bearings with shoulder bearings to guide your belt. Put F623ZZ -Box for mks tft 35 screen with support for installation on the Black Evo evolution. Two versions of brackets are available, for system and motedis profiles. -At firmware level, I had no programming to do, the screen is plug and play, plugged on a mks base v1.5 with the firmware of jjj for head z122 Links below -Firmware head z122 https://www.thingiverse.com/thing:2577212 Screen: https://fr.aliexpress.com/item/Makerbase-3d-imprimante-affichage-MKS-TFT35-V1-0-tactile-cran-avec-3-5-pouce-plein-cran/32891320510.html?spm=a2g0w.12010608.0.0.40cb81a6AdkJ1L