Chimera Zesty Nimble X-carriage for Prusa i3 clone

thingiverse

Having rebuilt my Prusa i3 Steel clone to use 10mm X-rods (https://www.thingiverse.com/thing:1905409), I designed this to use dual Zesty Nimbles (https://www.thingiverse.com/thing:1843195) on an E3D Chimera / Cyclops. It is designed to work with the X-carriage ends and other parts from that unit. It is a full set of printed parts and needs a number of bushes, bolts, nuts, magnets, shafts etc. I will try to list these but this is from memory - you may find you require other components, please let me know if you do so that I can update this page. The main components of this unit include: - a two-part X-carriage designed to accept 4x Oilite bushes (10mmID, 14mm OD, 10mm long). Eight M3 x 18 cap screws are required, as well as 8x M3 nuts. - an auto-level mount designed for a David Crocker IR auto-level board and attached to the main carriage with an M2 x 20 (IIRC) machine screw and nut. - a layer fan duct that is held in place by a number of 3mm x 4mm long rare earth magnets (5 in the duct and 5 in the carraige) - a mount for the two Zesty Nimbles and the Chimera / Cyclops. Note that this has some M2.5 captive nuts inside. - an optional filament monitor designed to use 2x 24 magnet discs. These printed discs use 24 1mm diameter x 2mm long rare earth magnets inserted alternately N-S-N. A length of clock spring 6mm wide, two hobbed discs, 4 Oilite bushes (3mm ID, 6mm OD, 3mm long) are required as well as a number of M2.5mm machine screw and nuts The duct, carriage and Main mount were printed in ABS, other parts in PLA. If there is interest then I will document and publish details of the filament monitor. Please message me here if so. Other parts designed for my printers include: - http://www.thingiverse.com/thing:1959901 (GT2 belt clamp (Prusa Y-axis) - http://www.thingiverse.com/thing:1937232 (Arduino Mega and RAMPS v1.4 case) - http://www.thingiverse.com/thing:1905409 (Prusa i3 steel 10mm upgrade) - http://www.thingiverse.com/thing:1959974 (Prusa i3 Steel Y-axis motor mount) - http://www.thingiverse.com/thing:1991116 (Prusa i3 Steel X-carriage) - http://www.thingiverse.com/thing:1991117 (E3D Chimera / Cyclops mount) - http://www.thingiverse.com/thing:1994413 (dual E3D Thermocouple amplifier board - housing) - http://www.thingiverse.com/thing:1090661 (Belt driven Bowden extruder with 1:2.5 reduction) - http://www.thingiverse.com/thing:896676 (enclosure for SevenSwitch FET) - http://www.thingiverse.com/thing:922455 (8mm Z-axis leadscrew bearing holder) - http://www.thingiverse.com/thing:922309 (Z-axis NEMA 17 adjustable endstop bracket) - http://www.thingiverse.com/thing:899607 (cable chain) - https://www.thingiverse.com/thing:2334269 (LCD housing) - https://www.thingiverse.com/thing:2377049 (PSU cover) - https://www.thingiverse.com/thing:2395715 (Chimera & Zesty Nimble drive cable spacer) - https://www.thingiverse.com/thing:2407651 (Chimera Zesty Nimble X-axis set for i3 clone) - https://www.thingiverse.com/thing:2436869 (A dummy NEMA 17 motor to hold the 5mm shaft) - https://www.thingiverse.com/thing:2748978 (A Duet WiFi housing) - https://www.thingiverse.com/thing:2749324 (A layer fan for the Smart Effector) - https://www.thingiverse.com/thing:2814068 (A Sannce I21AG mount for 3D printers) - https://www.thingiverse.com/thing:2844881 (A cooling duct for a Noctua 40mm fan on a Duet Smart Effector) - https://www.thingiverse.com/thing:2846955 (A quiet BerdAir type pump mount) - https://www.thingiverse.com/thing:3333609 (A Raspberry Pi case with 40mm fan) For avoidance of doubt, this item is licensed under a Creative Commons Attribution-NonCommercial-ShareAlike 4.0 International License. See http://creativecommons.org/licenses/by-nc-sa/4.0/ for more details.