Flux Delta spool bottom

thingiverse

Designed to cover the hole in the bottom of the spool area. This is useful if you have a spool that doesn't lay flat in the spool area, and need to be able to put a spool stand in the same area. I'm new to 3D printing, and this is my first model. I had some pretty bad plate adhesion problems when printing this. If you can tell me how to save the STL file so that it is 160mm wide, that would be helpful. Designed using Fusion 360 Print Settings Printer: Flux Delta Rafts: Yes Supports: No Notes: Scale to 160mm wide Raft: Yes (MUST) Skirt: Off (This can be done in advanced settings) How I Designed This Print Settings (Advanced -> Expert) avoid_crossing_perimeters = 0 before_layer_gcode = bottom_solid_layers = 4 bridge_acceleration = 0 bridge_fan_speed = 100 bridge_flow_ratio = 1 bridge_speed = 60 brim_width = 0 complete_objects = 0 cooling = 1 default_acceleration = 0 disable_fan_first_layers = 3 dont_support_bridges = 1 duplicate_distance = 6 end_gcode = G91\nG1 E-6 F300\nM104 S0\nG90\nM84\n external_fill_pattern = rectilinear external_perimeter_extrusion_width = 0.4 external_perimeter_speed = 25 external_perimeters_first = 0 extra_perimeters = 1 extruder_clearance_height = 20 extruder_clearance_radius = 20 extrusion_axis = E extrusion_multiplier = 1 extrusion_width = 0.4 fan_always_on = 0 fan_below_layer_time = 99 filament_colour = #FFFFFF filament_diameter = 1.75 fill_angle = 45 fill_density = 12 fill_pattern = honeycomb first_layer_acceleration = 0 first_layer_bed_temperature = 0 first_layer_extrusion_width = 125% first_layer_height = 0.3 first_layer_speed = 25 first_layer_temperature = 230 gap_fill_speed = 20 gcode_arcs = 0 gcode_comments = 0 gcode_flavor = reprap infill_acceleration = 0 infill_every_layers = 1 infill_extruder = 1 infill_extrusion_width = 0.4 infill_first = 0 infill_only_where_needed = 0 infill_overlap = 30% infill_speed = 60 interface_shells = 0 layer_gcode = layer_height = 0.3 max_fan_speed = 100 max_print_speed = 80 max_volumetric_speed = 0 min_print_speed = 3 min_skirt_length = 0 notes = nozzle_diameter = 0.4 only_retract_when_crossing_perimeters = 1 ooze_prevention = 0 overhangs = 0 perimeter_acceleration = 0 perimeter_extruder = 1 perimeter_extrusion_width = 0.4 perimeter_speed = 30 perimeters = 3 post_process = pressure_advance = 0 raft_layers = 4 resolution = 0.01 retract_before_travel = 2 retract_layer_change = 0 retract_length = 7 retract_length_toolchange = 10 retract_lift = 0.24 retract_restart_extra = 0 retract_restart_extra_toolchange = 0 retract_speed = 70 seam_position = aligned skirt_distance = 10 skirt_height = 1 skirts = 0 slowdown_below_layer_time = 15 small_perimeter_speed = 15 solid_infill_below_area = 1 solid_infill_every_layers = 0 solid_infill_extruder = 1 solid_infill_extrusion_width = 0.4 solid_infill_speed = 25 spiral_vase = 0 standby_temperature_delta = -5 start_gcode = G1 Z5 F5000 ; lift nozzle support_material = 1 support_material_angle = 0 support_material_contact_distance = 0.06 support_material_enforce_layers = 0 support_material_extruder = 1 support_material_extrusion_width = 0.4 support_material_interface_extruder = 1 support_material_interface_layers = 3 support_material_interface_spacing = 0 support_material_interface_speed = 100% support_material_pattern = rectilinear support_material_spacing = 2.7 support_material_speed = 40 support_material_threshold = 37 temperature = 215 thin_walls = 1 threads = 4 toolchange_gcode = top_infill_extrusion_width = 0.27 top_solid_infill_speed = 15 top_solid_layers = 4 travel_speed = 80 use_firmware_retraction = 0 use_relative_e_distances = 0 use_volumetric_e = 0 vibration_limit = 0 wipe = 0 xy_size_compensation = -0.07 z_offset = 0