FPV-Rover V1.21 (Tank)

thingiverse

--------------------------------------------------------------------- This is a remix version of the [FPV-Rover](https://www.thingiverse.com/thing:1240754) with increased clearance and reinforced hull. (you can see my other Rover modifications [FPV-Rover V1.31](https://www.thingiverse.com/thing:3867134) and [FPV-Rover V2.31](https://www.thingiverse.com/thing:3955659) ) Print 2 body parts, glue them together and tighten them with 4 studs! (see photo) You can secure various batteries and any electronics(arduino,raspberry/orange pi, etc) inside by inserting M3 nuts into the grooves (10mm step(v1.21) ). Added version of the housing the ability to install the rangefinder module HC-SR04 (or HY-SRF05, US-015, US-100) (see photo) In the 1_21_body version it is possible to easily attach or remove various rear modules The height of the useful volume of the body inside V1.21 - 44mm Purchased parts: - m3x40mm - 6pcs - m3x45(or 50)mm - 6pcs - m3 stud 120mm - 4pcs (I cut the stud 1m(3mm)) - m3 nuts - 20pcs or more - 3x1mm - 16pcs [magnets (50pcs package)](https://megabonus.com/y/Av5GQ) - 8x [bearings 6802zz](https://megabonus.com/y/bFuHc) for the main cog - 16x [bearings 688ZZ](https://megabonus.com/y/hgFL2) for the small cog - 4x [TT motor](https://megabonus.com/y/WytBf) - 2x [ECS](https://megabonus.com/y/wX7ps) Options - 1x [Servo](https://megabonus.com/y/NpFuI) - ?x [Fan 12v](https://megabonus.com/y/hz5wk) - 1x [HC-SR04](https://megabonus.com/y/7Zmoi) - 1x [Tie for holder Li-Po](https://megabonus.com/y/BDjFU) - 2x or more [Battery 18650](https://megabonus.com/y/pclgW) or [Battery 18650](https://megabonus.com/y/IBM4o) - 1x [2S 20A Li-Po Battery Protection BMS Board](https://megabonus.com/y/L34sF) - 1x [2s Balance cable for Li-Po battery](https://megabonus.com/y/bEF6h) - [Connector JST](https://megabonus.com/y/ezuKL) - 1x [Simple charger for 2-3s Li-Po](https://megabonus.com/y/bLDa3) - 1x [4CH Frsky Receiver](https://megabonus.com/y/2PNcj) or [8CH Frsky Receiver](https://megabonus.com/y/0gFa3) (if print EEZYbotARM MK2) - ?x BEC for protect rc-reciver: [Easy tuned BEC](https://megabonus.com/y/4bmAF) or [chiper BEC](https://megabonus.com/y/eiSuM) - 1x [Remote Control Lights Switch](https://megabonus.com/y/WYJgS) - 1x [Metal Scalpel Knife](https://megabonus.com/y/12sLy) Parts to print (I printed with Infill: 30%) - 1x body left v1.21 (see Print Setting Notes) - 1x body right v1.21 (see Print Setting Notes) - 1x inner track frame left v1.21 - 1x inner track frame right v1.21 - 2x outer track frame v1.21 - 1x fpv-cam-holder (I use [Micro FPV camera holder for FPV-Rover](https://www.thingiverse.com/thing:3351273)) - 1x holder servo - 64x track - 64x pins - 1x front - 1x back (5 version, choose which best for you) (Rover_v1_x1_Back_V1 or Rover_v1_x1_Back_2x18650BAT_hold or Rover_v1_x1_Back_AntennaHld or Rover_v1_x1_Back_anti-rollover_tail_with_fan_V0 or Rover_v1_x1_Back_anti-rollover_tail_with_fan_V1) - 8x small cog - 4x main cog - 1x top (v1,v2 with glue lock or v3 with screw locks) (also you can use this [base](https://www.thingiverse.com/thing:3686505) for mount [EEZYbotARM MK2](https://www.thingiverse.com/thing:1454048) ) - 1x set camera-led-mount - 1x led mount Options - 2x track outer cover (only for appearance) - 1x holder servo (see photo) - 1x Holder Battery V1 or 2x Holder Battery (see photo) - 1x Holder_30mm_Fan_for_video_transmiter_in_tail (see photo) - Holder 30mm Fan (see photo) - Cover 30mm Fan (see photo) Upgrade 01: http://www.thingiverse.com/thing:1269962 Upgrade 02: ~~http://www.thingiverse.com/thing:1700138~~ Upgrade 03: http://www.thingiverse.com/thing:1936491 Upgrade 04: https://www.thingiverse.com/thing:3686505 Upgrade 05 [Nerf Dart Launcher](https://www.thingiverse.com/thing:3835285) Upgrade 06 [robotic arm EEZYbotARM MK2](https://www.thingiverse.com/thing:3686505)