FPV-Rover V2.31 (Tank)

thingiverse

This is a remix version of the [FPV-Rover V1.31](https://www.thingiverse.com/thing:3867134) and [FPV-Rover V2.0](https://www.thingiverse.com/thing:2952852) with features: - speedy geared-motor with inner cooling fan and holes in sides of hull - increased clearance - raised front gear - reinforced hull [FPV-Rover V2.3 video](https://www.youtube.com/watch?v=AdfUW9qwpBw) [First test of solution](https://www.youtube.com/watch?v=0a3IIjsZuXM) Print 2 body parts, glue them together and tighten them with 4 studs! You can secure various batteries and any electronics(arduino,raspberry/orange pi, etc) inside by inserting M3 nuts into the grooves (step 10mm). Do initially the caterpillars from 33 tracks, after several trips remove 1 track and leave 32 tracks in caterpillars . The height of the useful volume of the body inside V2.3 - 44mm Purchased parts: - m3x45(or 50)mm - 8pcs - m3 stud 120mm - 4pcs (I cut the stud 1m(3mm)) - m3 nuts - 20pcs or more - 3x1mm - 16pcs [magnets (50pcs package)](https://megabonus.com/y/Av5GQ) - 8x [bearings 6802zz](https://megabonus.com/y/bFuHc) for the main cog - 16 x [bearings 688ZZ](https://megabonus.com/y/hgFL2) for the small cog - 2x [550 geared motor 12v 2300rpm Package A ](https://megabonus.com/y/WpC74) - 2x [ECS 160A XT60](https://megabonus.com/y/foKyv) - 1x or more 3s Lipo battery - 1x BEC for protect rc-reciver: [Easy tuned BEC](https://megabonus.com/y/4bmAF) or [chiper BEC](https://megabonus.com/y/eiSuM) - 1x [Grease for Plastic Gear xy-2 ](https://megabonus.com/y/p0h9q) Options - 1x [Servo 9g SG90](https://megabonus.com/y/NpFuI) - 3x [Fan 3010 12v](https://megabonus.com/y/hz5wk) - 1x [Tie for holder Lipo](https://megabonus.com/y/BDjFU) - 1x [4CH Frsky Receiver](https://megabonus.com/y/2PNcj) - 1x [Metal Scalpel Knife](https://megabonus.com/y/12sLy) - 1x spare part [0.5M 10T 2.0 gear](https://megabonus.com/y/UHi1I) for gearbox 37GB Parts to print (from FPV-Rover V2.31) (I printed with Infill: 30%) - 1x body left v2.31 (see Print Setting Notes) - 1x body right v2.31 (see Print Setting Notes) - 1x inner track frame left v2.31 - 1x inner track frame right v2.31 - 1x outer track frame left v2.31 - 1x outer track frame right v2.31 - 1x fpv-cam-holder (I use [Micro FPV camera holder for FPV-Rover](https://www.thingiverse.com/thing:3351273)) - 1x front - 1x back (5 version, choose which best for you) (Rover_v1_x1_Back_V1 or Rover_v1_x1_Back_2x18650BAT_hold or Rover_v1_x1_Back_AntennaHld or Rover_v1_x1_Back_anti-rollover_tail_with_fan_V0 or Rover_v1_x1_Back_anti-rollover_tail_with_fan_V1) - 8x small cog - 2x main cog - 2x rear main cog V2.3 - 2x small bevel V2.3 - 2x big bevel gear - 66x track (recomend vertical print with 100% infill) - 66x pins - 1x top (v1,v2 with glue lock or v3 with screw locks) (also you can use this [base](https://www.thingiverse.com/thing:3686505) for mount [EEZYbotARM MK2](https://www.thingiverse.com/thing:1454048) ) - 1x set camera-led-mount Options - 1x led mount - 2x inner protect long or short - 1x holder servo (see photo) - 1x Holder Battery V1 or 2x Holder Battery (see photo) - 1x Holder_30mm_Fan_for_video_transmiter_in_tail (see photo) - Holder 30mm Fan (see photo) - Cover 30mm Fan (see photo) Upgrade 01: http://www.thingiverse.com/thing:1269962 Upgrade 02: ~~http://www.thingiverse.com/thing:1700138~~ Upgrade 03: http://www.thingiverse.com/thing:1936491 Upgrade 04: https://www.thingiverse.com/thing:3686505 Upgrade 05 [Nerf Dart Launcher](https://www.thingiverse.com/thing:3835285) Upgrade 06 [Base for mounting EEZYbotARM MK2 to FPV-Rover](https://www.thingiverse.com/thing:3686505)