Illidan Stormrage

myminifactory

This model was tested in Cura 2.7.0. and print on an Ultimaker 2 in PLA material.Note: To maintain model quality, do not try to increase or decrease the size, since the joints may not fit and the model will not be assemble after scale changes.To avoid printing problems, we recommend the following settings:Quality Layer Height: 0.1 mmInitial Layer Height: 0.27 mmLine Width: 0.35 mmWall Line Width: 0.35 mm Outer Wall Line Width: 0.35 mm Inner Wall(s) Line Width: 0.35 mm Top/Bottom Line Width: 0.35 mm Infill Line Width: 0.35 mm Skirt/Brim Line Width: 0.35 mm Support Line Width: 0.35 mmInitial Layer Line Width: 100%Shell Wall Thickness: 1.05 mmWall Line Count: 3Outer Wall Wipe Distance: 0.2 mmTop Surface Skin Layers: 0Top/Bottom Thickness: 0.8 mm Top Thickness: 0.8 mm Top Layers: 8 Bottom Thickness: 0.8 mm Bottom Layers: 8Top/Bottom Pattern: LinesBottom Pattern Initial Layer: LinesTop/Bottom Line Directions: [ ]Outer Wall Inset: 0.025 mmCompensate Wall Overlaps: Check Compensate Outer Wall Overlaps: Check Compensate Inner Wall Overlaps: CheckFill Gaps Between Walls: EverywhereHorizontal Expansion: 0 mmInitial Layer Horizontal Expansion: 0 mmZ Seam Alignment: ShortestIgnore Small Z Gaps: CheckInfill Infill Density: 20% (all parts of the joints should be printed at 100% infill)Infill Line Distance: 3.5 mmInfill Pattern: GridInfill Line Directions: [ ]Infill Overlap Percentage: 10% Infill Overlap: 0.035 mmSkin Overlap Percentage: 5% Skin Overlap: 0.0175 mmInfill Wipe Distance: 0.0875 mmInfill Layer Thickness: 0.1 mmGradual Infill Steps: 0Infill Before Walls: CheckMinimum Infill Area: 0 mm2Material Enable Retraction: CheckRetraction Extra Prime Amount: 0 mm3 Retraction Minimum Travel: 0.7 mmMaximum Retraction Count: 90Minimum Extrusion Distance Window: 6.5 mmNozzle Switch Retraction Distance: 20 mmNozzle Switch Retraction Speed: 20 mm/s Nozzle Switch Retract Speed: 20 mm/s Nozzle Switch Prime Speed: 20 mm/s Speed Print Speed: 45 mm/s Infill Speed: 45 mm/s Wall Speed: 36 mm/s Outer Wall Speed: 26 mm/s Inner Wall Speed: 36 mm/s Top/Bottom Speed 20 mm/s Support Speed: 26 mm/s Support Infill Speed: 26 mm/sTravel Speed: 90 mm/sInitial Layer Speed: 27 mm/s Initial Layer Print Speed: 27 mm/s Initial Layer Travel Speed: 54 mm/sSkirt/Brim Speed: 27 mm/sMaximum Z Speed: 0 mm/sNumber of Slower Layers: 2Travel Combing Mode: AllAvoid Printed Parts when Traveling: CheckTravel Avoid Distance: 0.6562 mm Cooling Enable Print Cooling: CheckFan Speed: 100% Regular Fan Speed: 100% Maximum Fan Speed: 100% Regular/Maximum Fan Speed Threshold: 10 sInitial Fan Speed: 0%Regular Fan Speed at Height: 0.27 mm Regular Fan Speed at Layer: 2 Minimum Layer Time: 5 sMinimum Speed: 10 mm/sSupport Enable Support: CheckSupport Placement: EverywhereSupport Overhang Angle: 50°Support Pattern: Zig ZagConnect Support ZigZags: CheckSupport Density: 15 % Support Line Distance: 2.3333 mmSupport Z Distance: 0.1 mm Support Top Distance: 0.1 mm Support Bottom Distance: 0.1 mmSupport X/Y Distance: 0.7 mmSupport Distance Priority: Z overrides X/YMinimum Support X/Y Distance: 0.2 mmSupport Stair Step Height: 0.3 mmSupport Stair Step Maximum Width: 5.0 mmSupport Join Distance: 2.0 mmSupport Horizontal Expansion: 0.2 mmSupport Infill Layer Thickness: 0.1 mmUse Towers: CheckTower Diameter: 3.0 mmMinimum Diameter: 3.0 mmTower Roof Angle: 65° Build Plate Adhesion Build Plate Adhesion Type: BrimSkirt/Brim Minimum Length: 250 mmBrim Width: 8.0 mm Brim Line Count: 23Brim Only on Outside: CheckMesh Fixes Union Overlapping Volumes: CheckMerged Meshes Overlap: 0.15 mmSpecial ModesPrint Sequence: All at OnceSurface Mode: NormalExperimental Extra Skin Wall Count: 0Disclaimer: This model will look outstanding if printed on SLA/SLS 3D printer. The accuracy of the model printed on FFF printer can vary from the result shown in the pictures.