Porgs 3D Printing Figurines | Assembly

gambody

HISTORY OF THE PORGSPorgs are the sea birds that lived on the planet Ahch-To, where the Master Jedi Luke Skywalker was in exile a lot of years after the Battle of Endor. These animals, inhabiting on the rocks of the island where Skywalker lived. They build nests and can fly. Males of Porgs a little larger in size than females. These cuties conquered the hearts of all fans and our too. People even talk about their special importance in the plot. But we will not spread rumors and better just to present you the pretty Porgs who is now available for purchase on Gambody.ABOUT THIS 3D MODELPorgs 3D models for printing was created in ZBrush. The models are saved in STL files, a format supported by most 3D printers.Models of Porgs is available in 3 variants for each version (FDM/FFF, SLS/SLA):1. Angry2. Impressed3. CuteFDM version features: 
Each variant made as one piece with divided legs. Both files of feet (4_feet_R.stl) and (5_feet_L.stl) will fit for each variant of Porgs.SLS/SLA version features:
 Less than FDM and made as one piece in each variant of Porgs.All .STL files for 3D printing have been checked in Netfabb and no errors were shown.Note: Before starting 3D printing the model, read the Printing Details for CURA 2.7.0. software.There are 5 parts for FDM version and 3 parts for SLS/SLA.All parts of feet should be printed at 100% infill.FDM version dimensions:

- After being printed will stand: 109.3 mm tall, 150 mm wide, 116.4 mm deep - In Angry Variant.
115.3 mm tall, 114 mm wide, 106 mm deep - In Impressed Variant.
120.5 mm tall, 66.7 mm wide, 91 mm deep - In Cute Variant.
- Feet should be printed at 100% infill to make them solid.SLS/SLA version dimensions:
- After being printed will stand:54.7 mm tall, 75 mm wide, 58.2 mm deep - In Angry Variant.
57.7 mm tall, 53 mm wide, 52.9 mm deep - In Impressed Variant.
60.3 mm tall, 33.3 mm wide, 45.5 mm deep - In Cute Variant.WHAT WILL YOU GET AFTER PURCHASE?- .STL files of Porgs for printing which consist of 8 parts.
- 3 variants of Porgs: Angry, Impressed, Cute.
- Divided feet in FDM version which fit to each variant.
- Detailed settings that we provide for Cura 2.7.0 for the best print.
- High-poly detailed models of Porgs.
- Full technical support from the Gambody Support Team.Watch the video about Porgs 3D Printing Miniature at Gambody YouTube channel.  You can get Porgs Models for 3D Printing right now! Just click the green Buy button in the top-right corner of the model’s page. You can pay with PayPal or your credit card.Also, you may like another Space War 3D models.________________________On 12.01.2018 the new body was added for the impressed variant of the Porg. Now he is impressed looking up. The STL files are already available for purchase and download in “Source files” tab for both versions. You can find them at the end of the list. Here are the names of these files:_______FAQ: Where can I print a model if I have no printer?How to get started with 3D printing?How to set up my 3D printer?How to choose right 3D model print bed positioning? How to paint printed figurine?This model was tested in Cura 2.7.0. and printed on an Ultimaker 2 in PLA material.Note: All parts of feet should be printed at 100% infill.To avoid printing problems, we recommend the following settings:Quality Layer Height: 0.1 mmInitial Layer Height: 0.27 mmLine Width: 0.35 mmWall Line Width: 0.35 mm   Outer Wall Line Width: 0.35 mm   Inner Wall(s) Line Width: 0.35 mm   Top/Bottom Line Width: 0.35 mm   Infill Line Width: 0.35 mm   Skirt/Brim Line Width: 0.35 mm   Support Line Width: 0.35 mm Initial Layer Line Width: 100%Shell Wall Thickness: 1.05 mmWall Line Count: 3Outer Wall Wipe Distance: 0.2 mmTop Surface Skin Layers: 0Top/Bottom Thickness: 0.8 mm   Top Thickness: 0.8 mm       Top Layers: 8    Bottom Thickness: 0.8 mm      Bottom Layers: 8Top/Bottom Pattern: LinesBottom Pattern Initial Layer: LinesTop/Bottom Line Directions: [ ]Outer Wall Inset: 0.025 mmCompensate Wall Overlaps: Check    Compensate Outer Wall Overlaps: Check    Compensate Inner Wall Overlaps: CheckFill Gaps Between Walls: EverywhereHorizontal Expansion: 0 mmInitial Layer Horizontal Expansion: 0 mmZ Seam Alignment: ShortestIgnore Small Z Gaps: CheckInfill Infill Density: 20% (all parts of the feet should be printed at 100% infill)Infill Line Distance: 3.5 mmInfill Pattern: GridInfill Line Directions: [ ]Infill Overlap Percentage: 10%    Infill Overlap: 0.035 mmSkin Overlap Percentage: 5%    Skin Overlap: 0.0175 mmInfill Wipe Distance: 0.0875 mmInfill Layer Thickness: 0.1 mmGradual Infill Steps: 0Infill Before Walls: CheckMinimum Infill Area: 0 mm2Material Enable Retraction: CheckRetraction Extra Prime Amount: 0 mm3 Retraction Minimum Travel: 0.7 mmMaximum Retraction Count: 90Minimum Extrusion Distance Window: 6.5 mmNozzle Switch Retraction Distance: 20 mmNozzle Switch Retraction Speed: 20 mm/s    Nozzle Switch Retract Speed: 20 mm/s    Nozzle Switch Prime Speed: 20 mm/s Speed Print Speed: 45 mm/s    Infill Speed: 45 mm/s    Wall Speed: 36 mm/s      Outer Wall Speed: 26 mm/s      Inner Wall Speed: 36 mm/s    Top/Bottom Speed 20 mm/s    Support Speed: 26 mm/s      Support Infill Speed: 26 mm/sTravel Speed: 90 mm/sInitial Layer Speed: 27 mm/s
    Initial Layer Print Speed: 27 mm/s    Initial Layer Travel Speed: 54 mm/sSkirt/Brim Speed: 27 mm/sMaximum Z Speed: 0 mm/sNumber of Slower Layers: 2Travel Combing Mode: AllAvoid Printed Parts when Traveling: CheckTravel Avoid Distance: 0.6562 mm Cooling Enable Print Cooling: CheckFan Speed: 100%    Regular Fan Speed: 100%    Maximum Fan Speed: 100% Regular/Maximum Fan Speed Threshold: 10 sInitial Fan Speed: 0%Regular Fan Speed at Height: 0.27 mm    Regular Fan Speed at Layer: 2 Minimum Layer Time: 5 sMinimum Speed: 10 mm/sSupport Enable Support: CheckSupport Placement: EverywhereSupport Overhang Angle: 50°Support Pattern: Zig ZagConnect Support ZigZags: CheckSupport Density: 15 %    Support Line Distance: 2.3333 mmSupport Z Distance: 0.1 mm    Support Top Distance: 0.1 mm    Support Bottom Distance: 0.1 mmSupport X/Y Distance: 0.7 mmSupport Distance Priority: Z overrides X/YMinimum Support X/Y Distance: 0.2 mmSupport Stair Step Height: 0.3 mmSupport Stair Step Maximum Width: 5.0 mmSupport Join Distance: 2.0 mmSupport Horizontal Expansion: 0.2 mmSupport Infill Layer Thickness: 0.1 mmUse Towers: CheckTower Diameter: 3.0 mmMinimum Diameter: 3.0 mmTower Roof Angle: 65° Build Plate Adhesion Build Plate Adhesion Type: BrimSkirt/Brim Minimum Length: 250 mmBrim Width: 8.0 mm    Brim Line Count: 23 Brim Only on Outside: CheckMesh Fixes Union Overlapping Volumes: CheckMerged Meshes Overlap: 0.15 mmSpecial ModesPrint Sequence: All at OnceSurface Mode: NormalExperimental Extra Skin Wall Count: 0Disclaimer: This model will look outstanding if printed on SLA/SLS 3D printer. The accuracy of the model printed on FFF printer can vary from the result shown in the pictures.