Scythe Organizer for Original Box (Contains All Expansions and Add-Ons)

thingiverse

___ #Scythe Box Organizer there are a lot of Scythe box organizers on thingiverse. No One fit my idea of box organization. i wanted to use the original box in order to store all the pieces of the Scythe Boardgame and the first two expansions: - Invaders from afar - The Wind Gambit - Table Extension - Metal Coins - Realistic Resources - Promo Cards - 7 Combat Wheels So i start looking around, take measurement and stard designing my own box organizers. I had to admit that some of the ideas come from what i saw on other organizers, and mixed up tu fit everything ___ ###What you need to print? **7 Army containers:** Each box shall contain al the army specific items: wooden token, hero, mechs, ship and combat wheel. Pay attention that there are 3 differents box because of size optimization: *Boxes* + **Player_Box_Std:** you need to print 2 of them in order to fit White and Green Army. + **Player_Box_Lrg:** you need to print 2 of them in order to fit Red and Black Army that have larger mech bases (+1mm in diameter). + **Player_Box_Low:** you need to print 3 of them in order to fit Purple, Yellow and Blue Army. Those boxes are low since the mechs are shorter than others. + **Player_Box_Low_V2:** If you have airships you need to print 3 of those boxes instead of the LOW version, for Purple, Yellow and Blue Army. This Box has an increased box height of +2mm allowing ships to fit into the box *Lid* + **Player_Box_Lid:** This lid will fit every player box and avoid items to get out of the box (combat wheel cover wooden tokens, cover keep wheel in place and avoid miniatures to get out). + **Player_Box_Lid_NoHole:** This Lid is the same as the previous, but without the hole for the combat wheels. There is no marking on the lid. if you desire the Faction Logo please see the "Alternative Lid Set" Section. **Resource Container**: The resource box contains the 4 types of resource, the resource multiplyer tokens and also the encounter tokens. + **Resource_Box_Lid:** + **Resource_Box:** Resource box. It has the same height of the Plaer Box Low, in order to have a flat surface to place Game Board. + **Resource_Box_V2:** This new version is to print instead of the previous Resource_Box if you plan to print the V2 version of the Player box. It has an increased height on +2mm as per the 3 player box, in order to have a flat/leveled surface. **Card Holder** + **Large_Card_Tray:** This will contain encounter and factory Card (one over the other on the same hole) + **Small_Card_Tray:** This will contain objectve and automa Card (one over the other on the same hole), and combat cards plus game bonus on another space + **WoG_Card_Tray:** This tray only contains the 3 cardboard deck (card each) coming from Wind of Gambit, in 3 separates slots. it shall be printed 2 times that shall be glued togheter since it's size it's bigger than my print Area. a "full" version of the piece for bigger printer is included. **Coin Holder** I'm currently using the coin holder made by [Fringe](https://www.thingiverse.com/Fringe/about "Fringe") You can find it here: [Scythe Coin Holder](https://www.thingiverse.com/thing:2551923 "Scythe Coin Holder") ** Alternative Lid Set ** An anlternative Lid set has been developed by [Cunningham88](https://www.thingiverse.com/Cunningham88/about "Cunningham88") You can find it here: [Scythe Faction Lids](https://www.thingiverse.com/thing:3076259 "Scythe Faction Lids") Is still a WIP but could be great, especially if you do not have all the combat wheels.. Check-It out. ___ ### Box Organization: I suggest to see the pictures in order to understand how to place stuff: + Player boxes have to be placed in two levels, togheter with the reource box (that has the same height of the Low player boxes. I suggest to place the 4 higher boxes below, and the 4 lower boxes above. + On the side you place below the WoG card holder, then on top of it you polace the small and large card holders. + On the side you will find the place for thecoin holder. the army board shall be placed vertically on the mox side. + The action board shall be placed on top of the card holder. + On top of everything shall remain the place for the game board and the game board extension, allowing box lid to close perfectly. ___ ###ChangeList *14/08* + Thing Published *16/08* + Modified PlayerBoxLid (increased thickness to cover the combat wheel pin and avoid to bend while over the box) + Modified Resource Box (token hole are too tight to fit perfectly the tokens) + Card Trays Printed well. (note that has very low thickness. this hel to fit every thing and reduce print time. *18/08* + The Organizer is ready to be printed *31/08* + Found a bug on due to Airship size (101x33x41mm) on the 3 faction with low height profile. There is a V2 Version for the Player Box and Resource box with increased Height of +2mm. Take a Look. + Added a Version of the lid without the hole for combat Dials