1 3 8 threaded rod 3d models
1471681 3d models found related to 1 3 8 threaded rod.thingiverse
http://www.thingiverse.com/apps/customizer/run?thing_id=193647 Instructions Using the following options: socket_depth = 3.5 slot_depth = 2 countersink = 2 type = rod socket_facets = 6 texture = exclude head_diameter = 12 nut_thread_outer_diameter = 9...
prusaprinters
... using TinkerCad. ...You will need a 3/8" threaded rod with lock washers flat washers and two nuts to secure it.Recommend printing in PETG for durability at 0.2mm layer height.Paint on supports might be required, especially for the inner baffle.
thingiverse
Mount to attach a length of 3/8" threaded rod to the side of my printer. I have this attached to the 2020 extrusion frame of the printer, but you could use this to attach it to anything really: wall, cabinet, etc. ... I use 2 of these on my printer,...
thingiverse
These connectors are for use on 5mm output shaft steppers and 3/8" ACME threaded rod. Instructions 1) Print 2) Insert 5mm nuts into nut capture slots on bottom of the part. Start M5 x 10 SHCS into nuts 3) Clean up ACME threads if necessary- I used a...
prusaprinters
These connectors are for use on 5mm output shaft steppers and 3/8" ACME threaded rod. Print instructionsCategory: 3D Printer Parts Instructions 1) Print 2) Insert 5mm nuts into nut capture slots on bottom of the part. Start M5 x 10 SHCS into nuts 3)...
thingiverse
This is my remake for those who have high torque motors, i made a new rear axis for use of a 1/8 threaded rod, to reinforce it. You will need to make a little biig hole on the wheel lock nut for the 1/8 threded rod, then on each end put a 1/8 nylock...
thingiverse
http://www.thingiverse.com/apps/customizer/run?thing_id=193647 Instructions Using the following options: type = bolt thread_outer_diameter = 6.35 nut_height = 6 step_shape_degrees = 30 outer_diameter = 14 non_thread_length = 6 thread_length = 7...
thingiverse
I have a piece of 3/18" threaded rod, and I wanted to mount it with one end in a motor and one end in a bearing. I have cheap 608 bearings around, but obviously the outer diameter of the rod does not match perfectly with the inner diameter of the...
pinshape
For Prusa i3 Corners are offset 5mm to add a total of 10mm additional clearance when using 370mm linear rod and 380mm threaded rod for the Y Axis. The post traps the 8mm linear rod so no zip-ties are required to secure the rod. ...
thingiverse
Super sturdy mounts for 1 3/8" diameter rod for hanging clothes, etc. Printed in ABS. SUPER STRONG. ....2mm layer res, 50% infill, 4 shells all around
thingiverse
Yet another closet rod holder. ... The existing ones were just cheapy plastic, so I made these in Solidworks, and printed them in ABS at 80% (0.18mm layer). 1-3/8" (35mm) diameter rod.
thingiverse
http://www.thingiverse.com/apps/customizer/run?thing_id=15633 Instructions Using the following options: boltShaft = 3 length = 30 washer = 0 thickness = 4 trap = 2.4 gap = 0.3 shaft2 = 9.525 shaft1 = 5 wall = 1.6 offset = 2 bridge = 0.3 nut = 5.5...
prusaprinters
... I made these in Solidworks, and printed them in ABS at 80% (0.18mm layer). 1-3/8" (35mm) diameter rod. Print Settings Printer: Lulzbot TAZ 5 Rafts: No Supports: No Resolution: 0.18mm Infill: 80% Filament: Any ABS Any Category: Replacement Parts
thingiverse
Remix of: Parametric dust cap for bearing https://www.thingiverse.com/thing:754366 Designed to fit perfectly at the end of a 1 1/4" closet rod into a 1 3/8" pole socket. ... Diameter: 36 Rim width: 1.3
thingiverse
http://www.thingiverse.com/apps/customizer/run?thing_id=193647 Instructions Using the following options: resolution = 0.5 non_thread_length = 0 socket_facets = 6 non_thread_diameter = 19 head_height = 5 nut_type = normal drive_type = socket thickness...
thingiverse
http://www.thingiverse.com/apps/customizer/run?thing_id=193647 Instructions Using the following options: drive_type = socket head_type = hex nut_type = normal head_height = 5 slot_depth = 2 thread_length = 230 outer_diameter = 14 inner_diameter = 8...
thingiverse
http://www.thingiverse.com/apps/customizer/run?thing_id=193647 Instructions Using the following options: slot_depth = 2 non_thread_diameter = 0 head_type = hex inner_diameter = 8 countersink = 2 nut_diameter = 12 head_diameter = 12 thickness = 2...
thingiverse
http://www.thingiverse.com/apps/customizer/run?thing_id=193647 Instructions Using the following options: non_thread_length = 0 nut_thread_outer_diameter = 9 step_shape_degrees = 45 drive_diameter = 5 thread_step = 2 nut_height = 6 head_height = 5...
thingiverse
http://www.thingiverse.com/apps/customizer/run?thing_id=193647 Instructions Using the following options: facets = 6 non_thread_diameter = 0 inner_diameter = 8 thread_length = 146 head_height = 5 nut_thread_step = 2 nut_step_shape_degrees = 45...
thingiverse
http://www.thingiverse.com/apps/customizer/run?thing_id=193647 Instructions Using the following options: slot_width = 1 thickness = 2 resolution = 0.5 thread_step = 2 inner_diameter = 8 thread_outer_diameter = 8 step_shape_degrees = 45 nut_resolution...
grabcad
Generic 1/4 to 3/8 brass adapter.Manually measured.Designed in Fusion360.
thingiverse
Two will fit over a 1/8th inch (3.175mm) diameter launch rod. There are three with spreads on the horizontal support bars at 45, 60, and 90 degree as well as one that combines all three. The other two will fit over a 3/16th inch (4.763mm) diameter...
thingiverse
Model Rocket Rod Clamp sized 1/8" & 3/16". Bought a rocket launch pad that came with 1/4" hole/rod, but our rockets need a 1/8" to fit in its guide tubes. ...Built this out instead of paying $30+ for a whole new launch pad, since the clamp portion is...
thingiverse
http://www.thingiverse.com/apps/customizer/run?thing_id=193647 Instructions Using the following options: thread_length = 2 nut_type = normal thread_outer_diameter = 3/8 resolution = 0.5 head_diameter = 12 countersink = 2 texture = exclude...
thingiverse
http://www.thingiverse.com/apps/customizer/run?thing_id=193647 Instructions Using the following options: facets = 6 drive_type = socket nut_thread_step = 2 slot_depth = 5 type = rod step_shape_degrees = 45 thickness = 2 thread_length = 80...
thingiverse
Attempt to couple the 6mm shaft of a DC hobby motor to a 3/8" threaded rod to make a cheap linear actuator. ... Used M3 screws and hex bolts.
thingiverse
http://www.thingiverse.com/apps/customizer/run?thing_id=193647 Instructions Using the following options: head_diameter = 12 socket_depth = 3.5 nut_type = normal slot_depth = 2 drive_diameter = 5 drive_type = socket nut_height = 6 nut_thread_step = 2...
thingiverse
http://www.thingiverse.com/apps/customizer/run?thing_id=193647 Instructions Using the following options: head_diameter = 12 head_height = 5 wing_ratio = 1 nut_step_shape_degrees = 45 inner_diameter = 8 nut_thread_step = 2 facets = 6...
thingiverse
http://www.thingiverse.com/apps/customizer/run?thing_id=193647 Instructions Using the following options: wing_ratio = 1 thickness = 2 nut_step_shape_degrees = 45 outer_diameter = 14 slot_depth = 1.5875 head_type = hex facets = 6 slot_width = 1...