1 4 to 5 8 adapter 3d models
2892942 3d models found related to 1 4 to 5 8 adapter.prusaprinters
I created this, because i had to put a light, with a 5/8" inner thread, onto a tripod with a ¼" outer thread.you can simply screw it onto your ¼" thread with a screwdriver.I tested and printed this with petg, 0.2mm and 50% infill, works perfectly...
prusaprinters
This adapter fits between the hose for the pump and the hose for the heater. Tapered sides so that it didn't have to be perfect. *UPDATE: I wasn't happy with the original, the taper wasn't gradual enough to help and interfered with clamping. ...I've...
thingiverse
UNC 1/4" to 5/8" camera bolt adapter Print Settings Rafts: Doesn't Matter Supports: Doesn't Matter
thingiverse
You can use this to mount microphone stand adapter (with 5/8 thread) to a standard (1/4 thread) tripod. EDIT: v2 - 1/4 hole was too small on some FDM printers so I scale it a bit, now it should be fine. ... - Print it with adhesion because of the...
thingiverse
A few simple 1/4" 20TPI camera tripod mount to 5/8" 27TPI microphone holder adapters. ...Adapters 2 and 3 require a 1/4-20 nut pressed into them.
thingiverse
The adapter was designed to connect the laser level to a 1/4 inch tripod.
thingiverse
Adapter for Laser Levels with ANSI 5/8 thread to standard 1/4 thread of photo tripods. ... Fits well for ADA 2D Basic Level
thingiverse
Haven't found this elsewhere, so I've quikly designed one: 5/8-27 female to 1/4-20 male I use it to attach a camera mount to a microphone stand. ... Let me know, if it works for you
thingiverse
I wanted to put a shotgun mic on a small Manfrotto desktop tripod but could not find a suitable adapter, so I designed one. This works for me, as in: holes and threads are scaled so they printed well with my printer. Play with the scaling function of...
thingiverse
I made this adapter for putting a Laser Level 5/8" thread on a regular 1/4" photo tripod. The design is in openscad and you can adjust the base cylinder to suit (shown as r=15mm). The 1/4" thread is a bit tight so may have to run a test print OR...
thingiverse
Made this to stick my Cannon Camera to my Mic Stand. ...IDK if the threads are perfect or not as I printed this in a hurry but you should be able to get close with thin layers.
thingiverse
Designed to adapt a standard 1 1/4" sink drain to a 5/8" inside diameter tube. Print with 100% infill and coat the inside with epoxy to insure it's water tight. ...Happy camping!
thingiverse
thread adapter 1/4-20 to 5/8-11 used to laser level with photo tripod
thingiverse
... leave a comment about the scaling but couldn't find it. Having that said, I am not the designer of this piece. If anyone founds the original one, leave it on the comments or let me know so I can give credit to him/her and mark it as a remix. ...
thingiverse
Simple adapter to get you from a 1/4-20 camera mount to 5/8-11 for survey equipment or laser levels which is what I made this for. ...
prusaprinters
Simple adapter to get you from a 1/4-20 camera mount to 5/8-11 for survey equipment or laser levels which is what I made this for. Print Settings Printer Brand: Prusa Printer: I3 MK3S Rafts: No Supports: No Resolution: .15 Infill: 30% Filament:...
thingiverse
Screw adapter to attach a microphone clip to a standard camera mount e.g. ...on a tripod.
thingiverse
This threads into a microphone and allows a 1/4-inch camera or speaker mount to hold it. The design from groundwater wouldn't thread into my Snowball microphone, so I drew my own in Fusion 360. The nice thing about Fusion 360 is that I can create...
thingiverse
Since I needed to put my microphone on a stand for the camera. ...I create this 5/8"-27 Male to 1/4"-20 Female Screw Thread Adapter. ...Fit tight.
thingiverse
I needed an adapter from 5/8 male to 1/4 female to mount my Samson Meteor USB Microphone on a normal tripod. I've designed the 5/8 male part a little bit longer than necessary so you can also create a little arm for a pop filter and mount it in...
thingiverse
Something something not blank
thingiverse
Customized version of https://www.thingiverse.com/thing:2867489 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=2867489
cults3d
Adapter for my second airbrush Created at theOpenScad and can be converted to Customizer, but use some external library: - threadlib https://github.com/adrianschlatter/threadlib - threadprofile...
thingiverse
Adapter for my second airbrush Created at theOpenScad and can be converted to Customizer, but use some external library: - threadlib https://github.com/adrianschlatter/threadlib - threadprofile...
thingiverse
Adapter from photography standard tripod screws 1/4-20 to microphone 3/8-16 screws
grabcad
Just in case you are interested our team created a part to adapt 1/2" tube to 5/8"tube. We have printed it and it works great. You press the adapter onto / into the 5/8" tube (it goes over the outside and at the same time a bushing goes inside. It...
thingiverse
I needed a 1/4" to 3/8" adapter for an easy job, so 2 minutes in Tinkercad and 40 minute print and Bam. ... Not meant to replace a metal one but gets the job done for loose stuff and my 3/8" battery wratchet.