3d printer filament feeder
1941378 3d models found related to 3d printer filament feeder.grabcad
... feeder for 3D printer. ...Should be possible to control with an Ramps 1.4 controller. See my publishing back in 2013. This idea is also from that time. I did have it 3D-printed but I never finished the feeder or the printer idea. ...Have fun with it.
grabcad
for dual head. ...avoid wet atmosphere, put silica gel inside.
thingiverse
My 3D Printer (Anet A6) extruder's filament feeder had a metal screw that pushed down to change the filament... and it wasn't very "user firendly". I made a nice button, perfect for your thumb which fits snugly over that screw and makes changing the...
thingiverse
This is a really simple solution to substitute the original plastic bearing holder. You can screw in a M3 screw with a spring and you have an adjustable bearing pressure. No moving parts. I have used Thermec ZED material. Please enjoy! ...:)
thingiverse
FlashForge Dreamer 3D printer hook for filament. I have created hanging hook for Nunus 1 kg filament which is not fitting inside the printer's cabin. I started from another prototype http://www.thingiverse.com/thing:938750 I have than designed and...
thingiverse
This is a small size (95mm dia.) FIlament feeder design for small size inexpensive printers. ...
thingiverse
HICTOP (hic-top / hic top) 3D printer improved filament feeder model 3DP11 the new version (1Q2016) of Hictop printer includes a microswith to monitor filament. the problem is that it make a lot of noise because it don't let the filament freely flow....
thingiverse
Replacing the original filament clamp in the feeder from Artillery, modeled for the Hornet circuit, but this feeder is probably also on other models of Artillery printers Video review Artillery Hornet 3D Printer https://youtu.be/lol8ukreAlU This...
thingiverse
Filament Feeder, it can be applied to all aluminum frames ZONESTAR 3d printer, for example D805(Z5), D806(Z6), D808(Z8), Z9 and Z10 etc. ...3d printer, support 1KG filament roll.
thingiverse
And, of course a 3D Printer to print the bits! The Drive Gear must be no more than 12.5mm OD. Most of the Mk7 & Mk8 types are suitable. Most motors have a 5mm or 6mm shaft (you'll have to measure) whereas my geared motor has an 8mm shaft. My 8mm...
myminifactory
The Wanhao Duplictor i3 Mini is a fantastic little printer for printing with PLA, but Elastic (as well as Flexible filament) is too soft to be pushed through the nozzle with the standard feeder clamp's base. Elastic and Flexible filament opens so...
thingiverse
This is a upgraded UP! ...3d printer filament feeder, it has a cover now. ...The feeder is more stable now, combined with a micro switch, stepper motor and new feeder board Instructions print the feeder and cover
thingiverse
https://youtu.be/qE8cBWm1Nek More about design https://theveel.com/3d/horizontal-filament-feeder-for-printer-chamber/
prusaprinters
More about design https://theveel.com/3d/horizontal-filament-feeder-for-printer-chamber/ Print instructionsCategory: 3D Printer Accessories Summary More about design https://theveel.com/3d/horizontal-filament-feeder-for-printer-chamber/
thingiverse
Filament filter for 3D printer. 1.75mm filament. ...You will need to get a sponge for this.
cults3d
This is a stand that is used to support your 3d printer filament wheel while printing.
grabcad
3D printer filament extruder complete CAT designs(https://repetierinstallation.blogspot.com/)
thingiverse
Holds the typical 1kg wheel of filament (would fit reels of other width within about 5 mm) Requires four 22mm dia. ...bearings for rollers.
thingiverse
... correct for the 1.0, not the 1.0A printer. 1 user found that the 1.0A hole for the screw is off by 5mm. Instructions Printed with 20% density and 0.2mm using light supports on a DaVinci 1.0 printer. ...Requires a 6-32 screw and nut (1"+ in length).
thingiverse
Hubs for 3D printer filament. One hub is 52mm ,the other is 72mm and they both fit a 10mm shaft. This thing was made with Tinkercad. ...Edit it online https://www.tinkercad.com/things/lb6kx6xTd4S
grabcad
This little clip can be used to clamp the end of your filament (of a 3D Printer) to the spool. It won't unrole then :)I did both filament sizes: 1.75mm & 2.85mm, but I also added a version with equations, you can then choose between different...
thingiverse
Edit it online https://www.tinkercad.com/things/jpCjXy0Xuf2 Assortment of clips for 3D printer filament spools. If you have ever tried to untangle a roll of filament, then you realize how handy these are. I normally just print a bunch and put extras...
thingiverse
I have done some writeup about the circuitry required: https://www.randseq.org/2020/02/3d-printer-filament-joiner.html And here, adding an OLED display and rotary knob for a totally independent unit that does not need to be tethered to a PC:...
thingiverse
Please watch my Youtube video tutorial on how to build this: https://youtu.be/NhnJ6pyhUBw GRABCAD LINK(for 3D model files in .ipt/.iam/STEP format): https://grabcad.com/library/3d-printer-filament-roller-hex-nut-version-1...
cults3d
With this file you can 3d print a custom filament spool holder. Modeled off of the anycubic basic spool holder that came with the I3 Mega printer. You can print each part whatever color you desire! Completely 3d printed! ... Prints easy with no supports...
pinshape
Summary This is a simple filament guide, designed to bolt to the frame of a 3D printer. I couldn't find a simple guide on the various maker sites, so I quickly put one together in Fusion 360. I'm happy to send you the file, if you wish to modify...