3d printer part cooling duct

This fan duct and mount points a 40 mm cooling fan directly at the hotend for part cooling, something the RepRapGuru printer lacks from the factory. Inside the duct part exist locations for nuts (either M3 or 4-40) to be held in for the corresponding...

Filament cooling duct Simple snap on hotend fins For fan 30x30mm

This is a two-piece mounting bracket for a complete replacement of the print head of a CoLiDo 2.0 Plus 3D printer.

I designed this in Fusion 360 so I could mount a Titan Aero extruder on my Cetus3D MkII extended printer. I had a few design goals for this: 1) Tip of nozzle would remain is stock location (achieved within a millimeter or so) 2) Light as...

Whilst this is obviously not a satisfactory long term solution - unless you really like the duct tape asthetic - it does allow you to print out better quality parts to improve your printer. The squared off version is an attempt to make the stock fan...

This is a part cooler for removing the part from the bed quickly after printing, so you do not have to cool the entire bed down or wait as long. Uses two 40mm fans It uses the gopro style mounting bracket. I got the flexible arm from...

This is an upgrade to the part cooling fan for the Monoprice Maker select IIIp printer

The original file for the cooling duct had some thin walls and hollow sections which made the part difficult to slice. I fixed the modeling problems and added some basic fillets to the inside and outside of the part. ... They probably wont do anything...

The part cooling duct is 2 pieces and the lower part can be removed with 1 screw to ease in maintenance, cleaning, nozzle changes, etc. This is my first design to be uploaded to Thingiverse, so any feedback is appreciated and I would be happy to...

Part cooling duct for E3D Hemera.

Just a radial part cooling duct

part cooling 30mm fan duct part cooling duct e3d Titan mount

A simple duct for cooling filament on the bed.

... and it fits a 40mm fan. Since I now have a 3D model that I can modify I may make new versions to fit a 50mm and a 60mm fan if neeed to cool the extruded plastic quicker. ...I added a new fan duct that I think is a better more efficient design.

part cooling 30mm fan duct part cooling duct e3d Titan mount Print Settings Rafts: No Supports: NoResolution: 200 Infill: 20 Filament: PolyMaker PLA Category: 3D Printer Parts

new part cooling fan duct for Anycubic Kobra WIP

Since I now have a 3D model that I can modify I may make new versions to fit a 50mm and a 60mm fan if neeed to cool the extruded plastic quicker. I added a new fan duct that I think is a better more efficient design. ...

40mm fan duct for tronXY extruder to cooling the printing part

Modified part cooling duct to suit a E3D heater block . ...( the original wont fit properly)

40mm fan duct for tronXY extruder to cooling the printing part

Remixed in Tinkercad and Windows 3D Builder using mount area from thing 2814127 Replaces stock Ender part cooling fan duct. Printed with supports, bed only, have not tried without supports. ...

replacement filament cooling duct for better prints

... the AnyCubic Kossel. ... Fits the same 4 holes and uses the same 4 screws as the stock part cooling duct, but gives two-sided cooling of the printed part. ... Note that this duct must be removed to use the auto-calibration and auto-bed leveling probe.

Quick and dirty remix of the part cooling duct to fit "my" i3 mega bmg direct drive mod. I squished only the middle. ...

Replacement Part Cooling duct for the Wombot Exilis, should fit other models. ... Do not use any supports, turn off completely S3D.

A Beta part cooling duct for the Railcore 300ZL utilising a 5015 blower and proven nozzle geometry. The adapter plate has a slot for a captive M3 nut, and the duct will require an insert/ helicoil for the blower retention bolt. A duct version and...

This is a 3D printable part cooling fan air duct for a centrifugal fan that connects to the side of the MK8 direct drive extruder hot end. It is modeled to direct the air right underneath the heater block. I removed the original hot end cooling fan...

It works with the standard part cooling fan and assembly oft the Ender 3. I had some problems with other cooling mods, because they were to close to the Nozzle or to close to the heater block. That's why I decided to make my own mod. ... I hope you...

Hope my Duct can help someone looking for a cool and functional parts cooling Duct. For this you'll need: 12 M3x30 screws for the 3 fans 2 M3x16 screws to attach the Ducts H mount 3 M3x10 screws to attach the Ducts bar on the top and cable holder 2...

Hope my Duct can help someone looking for a cool and functional parts cooling Duct. For this you'll need: 12 M3x30 screws for the 3 fans 2 M3x16 screws to attach the Ducts H mount 3 M3x10 screws to attach the Ducts bar on the top and cable holder 2...