45 degree rod holder 3d models

Prints with no supports if stem is pointing up. ... designed for thru hole mount or in an 1/2 inch oar lock mount

This is a part that allows one to connect a angle rod with a plate or other surface at a 45-degree angle. ...The part also includes a small hole that best fits a #10 screw when tapped.

This is a microphone holder for putting two Shure SM57s in a 45 degrees angle. It can be mounted on a normal mic clip. ...Be sure to check the measurements on the attached screenshots for scaling

After making my 90 degree model, I thought I would try and shorten the footprint, so I bent the supports at a 45 degree angle to get the spool higher and closer. Mounts to the top 20x20 rail of your printer. Designed around a 3D Solutech spool, wide...

After making my 90 degree model, I thought I would try and shorten the footprint, so I bent the supports at a 45 degree angle to get the spool higher and closer. Mounts to the top 20x20 rail of your printer. Designed around a 3D Solutech spool,...

In order to control the sun throughout the day and give the lanai a warmer feel we decided to install tension rods and curtains around the lanai but this one corner gave us issues because the tension rods are designed for straight runs and the...

In order to control the sun throughout the day and give the lanai a warmer feel we decided to install tension rods and curtains around the lanai but this one corner gave us issues because the tension rods are designed for straight runs and the...

Remix of 310weber's Ender 3 Spool Holder Side Bracket 45 degree. I added screw mounts to both sides to make a more stable connection to the printer. ... Additional nuts and screws required (I believe 4 M5x10mm screws - if using all 4 mounting holes, 2...

Glue Gun mount for the small Harbor Freight glue gun. ... It's at a 45 degree angle so I can mount it on my stair banister where my work table is. ... a screw hole could be added, but I just use VHB tape.

A fixing a clothes rod at a 45° angle in a 90° corner. ...For 28mm clothes rod.

... The cam holder slides into the top corner of the Rigidbot. It sits offset and at 4 degrees with a 1/4" hole through it. ...this allows you to focus the camera at the center of the build area without having a bunch of moving parts shaking around.

side mounted SD card holder

Designed this Makita battery holder to use my available wall space more efficiently. ... Printing: PLA+ 0,2 layer 40 % infill no support necessary scale up to 101% if your battery doesnt slide in easily

This is an angled (45 degrees) curtain rod holder that fits a broomstick with around 23.6mm diameter. ... It's a snug fit so if you want some wiggle room print it with a couple percent above 100.

For 15 degree rod holders. ...Add some electrical tape for a tighter/waterproof seal.

30-degree rod holder that can be mounted to multiple things. ...Kayak, boat, anything you want.

Replacement part for IKEA cabinet clothes rail holder 45 degree Держатель штанги для одежды под 45 градусов в шкаф IKEA.

This design has not yet been tested so all feed back and criticism is wanted and accepted. ... I designed this rod holder to be mounted to any boat on the fly. ...It will need hardware to be mounted and function properly.

45 degree wall mounted spool holder, because my filament kept jumping around on the spool and making noise otherwise. ... Required 180x180mm build area and printed from PLA with 15% gyroid infill.

This is a 45 Degree Spool Holder adapter for the filament spool holder provided with the SV01. I personally need this because my work space did not have enough clearance vertically. To assemble this, you will need 1 extra T-nut than provided...

I liked the original design to put the lightstrip in a 45 Degree, but needed it to put on a beam. It needs to be secured with a small screw. ... The holder is designed for Philips HUE LightStrip, so it can be a little bit larger than normal lightstrip.

Holder for 45 degree bit adapter compatible with the popular Gridfinity organization system. ...Models available for a short and long version of the adapter.</p><p>I have designed different models for a variety of socket sets:<br><a...

As a result the included spool holder at 45 degree angle to the hotend needs to be used. The attached enclosure channel fits on top of the printer frame and supports the enclosure as well as guiding the filament. If using the enclosure to keep...

... bolts instead of 2 to fix to the printer, you will need two M5x10 bolts and two T-nuts more. So all in all you will need: 4 x M5x10 bolts 2 x T-nuts 2 x M5 nuts And reuse the two M5x8 mm bolts and two T-nuts from the default spool holder fixation.

with this you can hold square or round strips at 45° to plane sand, .... for mft 20mm holes... ... one type is with wall to fix the workpiece in place

I designed this side mount for the Ender 3. ...I 45 it and dropped it down so that it wouldn't interfere with the cable chain system. I used Cura 30% infill, wall line width at 0.3, no supports. ...it uses stock hardware and slides into the side rail

... ### What sets this one apart from other spray can holders is that this one is intended for being mounted in a vehicle. Thats is why it is wrapping the can so it remains in the holder even on bumpy roads and during strong braking and acceleration.

I got tired of having my ninjaflex binding in my guide tube of my makergear M2, which has a tight 180 degree curve, so I picked up some bearings and designed a spool reel that would fit above my printer, which is in a corner. I designed it to...

This is a simple spool holder that I made for my Lack enclosure but you can basically mount it wherever you want. 7/4/2017 I added a filament guide because the spool kept 'unspooling' itself (if that's a word hahaha) It's a friction fit and just...

shower curtain rod holder for 30 degree vaulted walls