8mm rod 3d models
106981 3d models found related to 8mm rod.thingiverse
Needed a rod for Ikea Lack Pi Cam Mount https://www.thingiverse.com/thing:2995408
thingiverse
Simple low profile 8mm rod holder. ...i'm using 3030 frame with M5 bolts but could fit 2020.
thingiverse
This will hold an a mechanical end stop on an 8mm rod. ... the holes on the end stop are 9.5 mm apart.
thingiverse
Clip for an 8mm rod. ...Print Settings Printer: Hypercube Rafts: Doesn't Matter ...
thingiverse
For 8mm rod. ...Print Settings Rafts: Doesn't Matter Supports: Doesn't Matter ...
thingiverse
Spoolholders that screw together, for use on a 8mm rod. ... ECO 3D FILAMENT: 250g spool ø52mm FLASHFORGE: 600g spool ø49mm & ø20mm CLASOHLSON: 1000g spool ø85 & ø53mm
thingiverse
Not sure of correct name for these but its for mounting 8mm rod. It accepts 3mm cap head bolts and traps a nut for clamping. ...
thingiverse
This is a simple clamp for an 8mm rod. ...I use it to hold a spooler on top of a prusa wood frame.
thingiverse
Remix of the Hypercube EFusion for those with 8mm Y rods. ...Fits a LM8UU bearing.
thingiverse
I made this to act as a stop on a 8mm steel rod. ...fits snug, no fasteners needed
thingiverse
8mm rod stopper to avoid x belt to bend z rods m2 screw + nut required Print Settings Printer Brand: Prusa Printer: Prusa Steel Rafts: Doesn't Matter Supports: No Resolution: 0.2 Infill: 85%
thingiverse
Models (all for 8mm rod): + Single (10mm) + Double (20mm) + Single (10mm) w/ACME Threads 2mm pitch (single start) Clamp uses M3 20 screws to clamp. I suggest thread lock on anything moving like this that might encounter vibration. ... UPDATE -...
thingiverse
Made this for the shop, to hold a standard papertowel roll. ...It uses an 8mm rod to hold the roll. ...Just mirror it to print it for both sides.
thingiverse
I wanted a simple and easy clamp to hold my spool onto an 8mm threaded rod. ...I didn't like any of the other clamps I saw so I made my own. It has a 7.75mm center hole so that it can clamp onto the 8mm rod well.
thingiverse
... Allows to support a 8mm rod. On the base there are 4 holes for M3/M4 screws. You can screws it on woood, plastic etc... On the side i also placed 2 hole so that you can insert M3 nuts and insert M3 screws to prevent the 8mm rod from moving.
thingiverse
I only made this because I searched for "8mm rod" on Thingiverse and couldn't find one - instead, there are lots of accessories that go along with 8mm rods for 3D printers, but if an actual 8mm rod exists here, I couldn't find one. I didn't even...
thingiverse
The part mounting holes can accept 6mm bolt hardware, and there is a single 3mm x 22mm screw (with nut pocket) that is used to tighten the user's 8mm rod in place. The mount's overall size is about 53mm L x 20mm W x 34mm H and the 8mm rod (center)...
thingiverse
this is a 8mm rod holder i made, it is a work in progress. It is designed to have the rod inserted on one end and then have the holder screwed to a board. ...I made it for a small ornamental windmill in my backyard that I want to attach to the roof of...
thingiverse
Endstop switch mount for 8mm rod. Clamps onto rod and can be secured (if needed) with tywrap. Remix of https://www.thingiverse.com/thing:2932583, added holes for mounting screws and tywrap slot. Added lines to end of Openscad source (attached) to...
thingiverse
I designed this wire roll holder specifically for my desk (to be mounted to a horizontal 2x2). ...But it might come in handy for others as well. Use a 8mm rod between the two prints as a bar to hold the spools.
thingiverse
8mm rod mounting block. Uses a 4mm cap head screw and nut for the pinch, and 6mm cap head screws for the base. ...Print Settings Printer: Monoprice Replicator 1 Clone ...
thingiverse
There are 2 files: -8mm hole trough hole -8mm 15mm depth You can try whatever you want You will need to print: -2 x 8mm rod holders -2 x 8mm rod holders (mirrored with your slicer) For setup: - i recommend you to assemble the rods, linear bearings...
cults3d
There are 2 files: -8mm hole trough hole -8mm 15mm depth You can try whatever you want You will need to print: -2 x 8mm rod holders -2 x 8mm rod holders (mirrored with your slicer) For setup: - i recommend you to assemble the rods, linear bearings...