anet a8 3d touch

My variation of the Anet A8 3D Touch Mount

A simple bracket to fit a 3d touch sensor onto the Anet A8. Connection to the X-carriage might need longer bolts than stock, the holes are a tiny bit tight too Marlin configuration is included. ... See [OderWat's excellent...

This needs slightly changed firmware settings as follows: #define X_PROBE_OFFSET_FROM_EXTRUDER -26 #define RIGHT_PROBE_BED_POSITION 194 Some links to more information: Marlin and auto levelling:...

Home 3D printer 2. M851 Z0 - Reset Z0Offset 3. M500 - Store setting to eeprom 4. M501 - Set active parameters 5. M503 - Display Active Parameters 6. G28 Z0 - Home Z Axis 7. G1 X110 Y110 F1200 - Move nozzle to 0,0 8. G1 F60 Z0 - Move nozzle to...

This is a minimal mounting bracket for a 3D touch on an Anet A8. The bracket attaches to the top left of the X-axis bearing and fits between the fan and the X-Axis rails. I used a couple of zip ties to hold the 3D touch wires out of the way. ...For me...

To mount this sensor, you will need two M3x10 (minimum) and two nuts. I have printed this mount on PETG, but you can print on any material. ... Marlin settings for this mount: define LEFT_PROBE_BED_POSITION 45 define RIGHT_PROBE_BED_POSITION 175...

To mount this sensor, you will need two M3x10 (minimum) and two nuts. I have printed this mount on PETG, but you can print on any material. ... Marlin settings for this mount: define LEFT_PROBE_BED_POSITION 45 define RIGHT_PROBE_BED_POSITION...

The original was too small for me, current is cut out for Geeetech 3D touch to fit (13.6 x 13.8 mm). Might be possible, that you'll have to resize it to 10%. ... If you build it without support, than screw overhangs will be affected (but still good).

I made this bracket because all the brackets I find on the www places the sensor either in front of or behind the print nozzle. This does not work for me since I attach my glass plate with bulldog clips, for example; if the sensor is +40 in front...

This 3DTouch holder sits in place of the spacers at the bottom of the heatsink just behind the fan and allows the 3DTouch to sit in front of the nozzle.

It is fixed by the mounting screws of the two fans. Stable, so it provides accurate measurement. The height of the head can be adjusted by changing the height of the insert. For me, it was 5 mm. ...Before slicing, you can change the Z height as...

This remix have a shorter reinforcement to the rear, allowing [X Belt holder](https://www.thingiverse.com/thing:2016779) to be installed. It is based on BLTouch Smart version. **Marlin parameters, from [original...

Designed up this dealer button to use in home games or have just as something laying around for any poker fan. It was inspired by a dealer button in Pokerstars VR. Printing: Ring - Infil to add weight, supports needed for spade inset. Letter...

Studiando un po tra le varie soluzione mi sono creato un sistema che mi facilita la sostituzione del filamento e che mi permette di raffreddare il materiale.

Edited Dalewh's model, so it could fit a standard extruder motor from an Anet A8 (42SHDC3025-24B motor). Also changed the way the extruderfan is mounted. You can now use a bolt and a nut to attach the fan. It is also possible to tighten the...

I've made a simple remix of Air Duct and 3D Touch sensor holder for Anet A8. ... Added place for 2 LED.

... mount. ... The AM8 hemera I am using places the nozzle too low for the BL touch to work. This design allows the BL touch to be mounted in 4 different positions (top, bottom, and two middle positions) so you can set the most optimal BL Touch Position.

remixed this remix as the orig had errors in the stl shaved off the front and rear to make it look less bulky, raised the bl touch by 2mm for better clearance while printing offsets: define X_PROBE_OFFSET_FROM_EXTRUDER -28 define...

This mount is a Remix of https://www.thingiverse.com/thing:3068105 for ANET A8 Adjusted mounting holes for sensor and modified for clear visibilty of sensor status(Blue LED) for 3D touch clone from aliexpress...

Modifications in the firmware Marlin 1.1.8 : <blockquote> <p>#define X_PROBE_OFFSET_FROM_EXTRUDER -26</p> <p>#define Y_PROBE_OFFSET_FROM_EXTRUDER -37</p> <p>.</p> <p>.</p> <p>.</p> <p>#define LEFT_PROBE_BED_POSITION 26</p> <p>#define...

TL-Touch Smart holder for Anet A8 I was looking for a TL-Touch holder for my Anet A8 that did not require me to remove the fan or heatsink. I also wanted to print in PLA. Since I could not find anything I remixed the 3D-Touch mount from here...

Printed in PETG or ABS if you use PLA the heat of the extruder will bent it slightly over time. ...

Designed up this dealer button to use in home games or have just as something laying around for any poker fan. It was inspired by a dealer button in Pokerstars VR. Printing: Ring - Infil to add weight, supports needed for spade inset. Letter...

Designed up this dealer button to use in home games or have just as something laying around for any poker fan. It was inspired by a dealer button in Pokerstars VR. Printing: Ring - Infil to add weight, supports needed for spade inset. Letter...

... download pronterface send G28 //down to check the nozzle is't crash with the bed //up over the bed G1 x110 y110 F6000 //and down carefully. //put a A4 white paper in the bed //down at touch the paper //measure gap left //set gap //repeat

This is a remix of https://www.thingiverse.com/thing:2369995 to accommodate the 3dTouch sensor. ... Added Fusion360 and STP files.

Support "Touch-Mi" pour Anet A8 Se fixe par les 2 vis de maintien du ventilateur d'extrudeur (en lieu et place de la grille de protection). ... define X_PROBE_OFFSET_FROM_EXTRUDER -25 define Y_PROBE_OFFSET_FROM_EXTRUDER -42 define...

Anet A8 BL Touch Mount A mount to hold a BL Touch Sensor to an Anet A8 I needed a mount that would hold a BL touch sensor to my stock Anet A8 carridge. This design works using the fan mounting holes on the front of the carridge (the fan is then...

Anet A8 BL Touch Mount A mount to hold a BL Touch Sensor to an Anet A8 I needed a mount that would hold a BL touch sensor to my stock Anet A8 carridge. This design works using the fan mounting holes on the front of the carridge (the fan is then...

A mount to hold a BL Touch Sensor to an Anet A8I needed a mount that would hold a BL touch sensor to my stock Anet A8 carridge. This design works using the fan mounting holes on the front of the carridge (the fan is then screwed back in place over...