asi2600 zwo 3d models
377 3d models found related to asi2600 zwo.myminifactory
I wanted a simple cable guide for my ASI 2600 that was very easy to remove, and worked with the AstroZap aluminum dew shield. I do not mine the minor star diffraction spikes this produces. I printed two, they just slide on over the cables. ...
thingiverse
PENDING MODIFICATION OF THE DISSIPATION SYSTEM Refrigeración para cámara ZWO ASI 120 mc por dos células peltier y controlado por un Arduino nano un relé y un sensor de temperatura LM35. Todavía esta en desarrollo. ... PENDIENTE DE MODIFICACIÓN DEL...
grabcad
ZWO ASI 1600MM Pro, Astronomy camera mostly modelled, not the circuit boards inside
thingiverse
Laser bracket for the finder shoe on the ZWO AM5. ... Easily polar align.
thingiverse
Two versions of cable clips for the ZWO ASIAir Plus and ASIAir Pro astrophotography computer. ...
thingiverse
This is a cable relief for the ZWO EAF You can use a cable tie around it to secure to the EAF unit
thingiverse
I designed this simple pedestal to be able to place my ZWO AM5 on a simple plane. ... To be printed with layer 0.2 and infill 30-40%.
thingiverse
I like to have things I may need close and handy so I designed a holder that clips to my tripod to hold my ZWO EAF.
thingiverse
Brackets needed to substitute the iGuider camera for a ZWO Mini camera on the iOptron CEM70G mount. ... This will allow the ZWO ASIAir pro to be able to see the camera and utilize the built in optics that are present on the mount.
thingiverse
Adapter for ZWO EAF (electronic auto-focuser) . ...After detaching focuser knob in VC200L Vixen telescope, you are able to install your EAF and autofocus your frames during astrophotography sessions.
thingiverse
Peltier Cooler Housing for ZWO ASI178 Camera. You'll also require - 40x40x10mm 5v Fan 40x40x10 Heatsink 20x20x5mm 5v 1A Peltier Module Model No. ...TEC1-04901 9-36v > 5v DC Buck Step Down Transformer Heatsink Compound 4x50mm Nylon Screws
thingiverse
One fits (badly) on the ZWO camera lens itself. Friction-fit only. The other holds the ZWO camera body and the stepper motor. The stepper motor is this one : https://ebay.to/2WYtGDV Take care: the motor gets HOT, so settings for the driver...
thingiverse
... focuser system on a OAG. ... It will fit the ZWO OAG and the ASI174MM Mini. ... This will work perfectly with [Ardufocus](https://ardufocus.com) which is able to drive two independent focusing motors from one controller with full ASCOM support.
thingiverse
This is a Low Profile Cover for ZWO ASI Cameras. It makes it possible to reach back focus on the coronado PST telescope. ...Be careful when you take the original cover off, not to lose the protective glass window and its rubber gasket.
thingiverse
Mounting platform for a Mele Quieter II mini PC or ZWO ASIAIR computer. Uses existing 4mm mount holes and has a lip which securely hooks over the AM5 mount. I printed on edge using supports so the filament orientation would have the most...
thingiverse
The holder is designed to be used when you are attaching a short focal length lens directly to the ZWO camera -not recommended for lens over 135mm. To attached the the bottom part of the clamp to the dovetail requires two 10-24 3/4" machine...
cults3d
The holder is designed to be used when you are attaching a short focal length lens directly to the ZWO camera -not recommended for lens over 135mm. To attached the the bottom part of the clamp to the dovetail requires two 10-24 3/4" machine screws...
prusaprinters
This is a replacement end piece for ZWO's EAF Bracket. This was designed primarily for use on the ASKAR FRA400 telescope, however it should be useable on other ASKAR telescope focusers,</p><p> </p><p>I've printed this in Orange PETG, but it...
thingiverse
I took the stock rear image of the 2600MC available on the ZWO website, and scaled it to 90mm in PS. I then printed it out and took my measurements off the printed image. The USB cables should be a standard size so this should work well for...
thingiverse
The case will most likely hold other similar cameras from ZWO, dimensions are: Inner diameter (where the camera sits): 64mm Height (incl. 5mm for foam padding): 70mm There's a version of the lid for single colored prints without logo. Print...
prusaprinters
I've added a foam padding made from the foam that came with the original box. The case will most likely hold other similar cameras from ZWO, dimensions are: Inner diameter (where the camera sits): 64mm Height (incl. ...5mm for foam padding): 70mm</p>...
thingiverse
Remix of the great swiss body support for ZWO ASI2600MC PRO, modified for ZWO ASI294 PRO