ath m50 cable mod 3d models
125333 3d models found related to ath m50 cable mod.thingiverse
This is a gift for people having 3d-printer and ath-m50 broken hinge, you can print this too as a preventive device to not broke your precious headphone. All original movement is kept. https://youtu.be/cE3rPkuEhUY The dimension is for 3...
thingiverse
This thing is a replacement hinge for the Audio Technica ATH-M50. ...I designed it after attempting to glue the original hinge back together 5 times and having it snap again a few weeks later.
thingiverse
The nub preventing my ATH-M50 earpiece from rotating too far back broke off and was lost. Saw other methods of fixing this but many required taking the head phones apart or drilling into it. I wanted a quick solution that didn't require much...
thingiverse
The hyperair's version slightly did not match my m50. I changed the model for my headphones. Changes: 1. Reduce bar size for 5mm (23.87 -> 18.87) 2. Reduce hinge pins diameter 3. Add flat part to hinge pins 4. ...Fix the list of included files...
thingiverse
To save the end part of the cable when positioned upright and give it a bit of a relief
thingiverse
This is used so that I don't have to cut into my inner headphone housing to fit the jack, as is done in [this instructable.](https://www.instructables.com/id/Audio-Technica-ATH-M50s-removable-cable-mod/). I printed in Amazon PETG at 0.2mm. ...Could...
thingiverse
Clip for holding the Audio Technica ATH-M50/x Headphones. Designed for when folded up. ... Just press both tabs and remove.
thingiverse
Had trouble fitting the original adapter to ATH-M50s so this is a remix that I managed to make fit.
thingiverse
This is an adapter for putting SHURE SRH-480 pads on Audio Technica M50 headphones. ...more information and photos about this here:https://harariprojects.com/2015/03/10/3d-printed-headphone-pad-adapter/
thingiverse
I'm going on a trip and I needed a way to easily hold my Bluetooth adapter to my headphones. I bought <a href=https://www.amazon.com/gp/product/B075F1DV91/ref=oh_aui_detailpage_o01_s00?ie=UTF8&psc=1>this adapter</a>. The mount prints in two parts and...
grabcad
Decided to do something a little harder and modeled my headphones
grabcad
Just a quick model of these great headphones I had lying around. Dimensioning was mostly done by eye so it is not 100% accurate. The cord in the assembly is fixed so the mates on that side won't work. ... Feel free to remove the part or the references...
thingiverse
http://www.thingiverse.com/apps/customizer/run?thing_id=45424 Instructions Using the following options: tagH = 20 length = 100 width = 50 textT = 5 Font = write/orbitron.dxf build_plate_manual_y = 100 build_plate_manual_x = 100 edge = 5 tagThickness...
thingiverse
Hook for Audio Technica ATH-M50x headphones that also includes a hook for cables. The top hook matches the width of the headband of the ATH-M50xs. ...The backing was designed for use with 2 medium sized command strips and can be put anywhere you can...
thingiverse
I often use my ATH M40x headphones without the Modmic attached, so have a quick clip system instead of using the default clips is much handier. They're roughly designed after the default modmic clips, but moreso iterated for a tight, no-slip clip on...
thingiverse
print 2, one for each side. Then I used a cut up sock as the strap itself but you can use whatever fabric you want as long as its not too thick. ... Good luck
thingiverse
Things you need: - 2x DB37 connectors (male & female) - Some cable - Some screws (spare screws from CR-10 will do the trick) - Printed connector box - 2x printed DB37 housing - Some patience when soldering all the wires :) I've used an old printer...
thingiverse
Instructions Minimal instructions if you have a stock printrbot print a extruder-to-bodwen and a bowden-to-hotend Install the Pneufit adapters on your bowden cable and screw it onto the 2 printed pieces install this on your printer Extended...
thingiverse
I made this after printing some of the original and catching my thumb in the ratchet :-( this little mod saves your thumb :-) Flip the model 180 degrees to get the longest side on the print bed. ... 70% fill 0.2 res Thanks again to Mike
thingiverse
... USE AT YOUR OWN RISK!! The OP had a nice cross section that seemed to be great for a wire loom. I printed and tested the first design. The ball and sockets fit together with very little finishing to move smoothly. So i made it fit for the Mod-T
thingiverse
An update to thing:697545 by MechEngineerMike to make it snap-together. ... [3/10/15 update: sorry for the duplicate files in the first version... it's my first upload] Instructions Full size for extensions cords, scale at .5 for small cables.
thingiverse
... as possible and with as much style as possible then ORIGIN's M50 is for you. ...Featuring supercharged engines that counter a tiny weapons loadout, the M50 is a ship for going FAST. ... [Roberts Space Industries](http://robertsspaceindustries.com)
grabcad
"The Ontos, officially the Rifle, Multiple 106 mm, Self-propelled, M50, was an American light armored tracked anti-tank vehicle developed in the 1950s. ...It mounted six M40 106 mm recoilless rifles as its main armament, which could be fired in rapid...
thingiverse
An M50 Ontos, in roughly 1/48 scale. I couldn't find an Ontos on thingiverse, so I tried my hand at modeling one. Vehicle was modeled with the intention of printing it in 1/72 and 1/100 scale so some things are a little oversized to allow for easier...
thingiverse
Customized version of https://www.thingiverse.com/thing:3395463 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=3395463