betaflight 3d
1634409 3d models found related to betaflight 3d.thingiverse
My second attempt at building a dual-copter, this time with a 3d printed frame and using an X-Racer F3 flight controller running betaflight. Initial hover tests look promising and it flies much better than my previous attempt using a KK2 flight...
thingiverse
ESC covers for Betaflight 32bit ESC. It already saved my ESC from props strike (see photos). ...Doesn't cover LED so you can be visible during your flight.
thingiverse
ESC protector for the 35A Betaflight ESC. Mountable with 2 small zipties through the cutouts.. Print with the flat (top) side down, no supports needed. Best printed in TPU, more infill will make it tougher, less infill will make it lighter. ...I...
thingiverse
Going a little crazy with all the Logos :) But anyways :) This is a keychain that uses the Betaflight Bee Brain Logo and I incorporated a 5mm Propeller Wrench as well as a 1/4 Hex Socket for Screw Driver Bits etc. Was going to make the bee stinger a...
thingiverse
Check it out on github here: https://github.com/betaflight/betaflight Or follow a build guide on my blog here: https://nathan.vertile.com/blog and build your own miniquad! ...Print Settings Printer: Prusia i3 ...
thingiverse
This is a soft mount holder designed for the Betaflight F3-F4 Flight Controller. The little triangle points forward to fit the FC perfect. TPU in 5-10% infill. Use supports and stand on slotted end in 3D printer software. ... Cut to height needed.
thingiverse
Matek_BetaFlight_FC_F722_SE Dummy in .STL for printing and .STP for creating something new around in CAD.
thingiverse
Made a support to screw my betaflight matek f405 board directly to the Tricopter-LR middle plate. ... The support is held to the frame by the tail arm screws and te FC board with 10mm M3 screws
thingiverse
This is a 12mm Buzzer mount for Betaflight F3 and F7 flight controllers, distributed by FPVMODEL. It will likely fit any flight controller with 30mm mount hole spacing, or should fit on and frame with 30mm spacing holes. I printed it with...
thingiverse
This is a cover for the cnhl battery xt60 plug with the betaflight logo. It may not fit into other plugs because of the dimensions of the fittings. Printed on PLA with 2mm resolution gave a perfect finish. You may need to make some adjustments to...
thingiverse
... à partager vos créations et améliorer le concept! Pour le montage il suffit juste de visser 4 moteurs de chaque coté, une roue sur chaque et voila. /!\ Le chassis est fait pour des moteurs de 3" type 1407. Config betaflight en dessous ->
cults3d
... weight of 2.56gr. No need to use supports. Look for the file "protetor_esc_betaflight_v2.stl" The red one was printed in the new version (PLA) Edited: July, 25th - Included a short version without the clamp to fit in any frame and to become lighter.
thingiverse
... of 2.56gr. No need to use supports. Look for the file "protetor_esc_betaflight_v2.stl" The red one was printed in the new version (PLA) Edited: July, 25th - Included a short version without the clamp to fit in any frame and to become lighter.
thingiverse
The rx little board goes onto the 3d printed "shelf". For a smaller version with 7mm motors check here: https://www.thingiverse.com/thing:3339106 Default settings in INAV and Cleanflight work. ... For better stability and responsiveness...
thingiverse
This is the Wall art version of the Betaflght logo. Can be attached using the standard 3M command strips. ... Please comment with any improvements
thingiverse
This is a wall mount for racing or freestyle drones with a betaflight logo to break the monotony.
cults3d
This is a wall mount for racing or freestyle drones with a betaflight logo to break the monotony.
thingiverse
Modified model of the bottom part for the quadrocopter Cetus X. I made 2 types for each model, one type for use with motors connected to connectors, the second type for soldered motors, with through holes for wires. Made to install GNB batteries,...
thingiverse
Have your SD card fly out like me in a crash? This case/holder for your dataflash storage will keep your SD card in place no matter how hard you hit the ground. ...Print Settings Printer Brand: RepRap ...
thingiverse
This box is used for mounting a 30x30 standard sized flight controller for use as a receiver for a Betaflight to USB PC Gaming device. Mount the flight controller as you normally would in a stack (don't need to care about soft mounting since the...
cults3d
Update - april, 2019 I made a new version with high quality that will result in a much more defined and beautiful print. This new version fits much better on the stick and with a change in the tip of the wing of the wasp, the protector gets much...
thingiverse
I hope this helps others aswell, I made this because of the ESC's high profile I kept cutting off ESC parts with my props or even by clipping branches. Printed using a FlexionExtruder, with supports for the LED holes etc. ... This thing is ment to...
thingiverse
Wraith 32 35A BL Heli 32 ESC Protector tpu PFV Channel: https://www.youtube.com/channel/UCQ3t5Uuk7z8JMLDsON8KfxQ
thingiverse
Update - april, 2019 I made a new version with high quality that will result in a much more defined and beautiful print. This new version fits much better on the stick and with a change in the tip of the wing of the wasp, the protector gets much...