camera rails 3d models

Parts for a stopmotion camera rail

this is a rail mount hanger thingy for use with 8mm diameter camera rails on 50mm center-to-center spacing.

Parts for a stopmotion camera rail Print instructionsLicence: Creative Commons - Attribution - Share Alike Category: Parts

This 15mm Camera Rail (60mm) system is made for Sony A6_00 Cameras with Smallrig Camera Cage. I get the rails on my local hardware store. 15mmx100cm so I made two 30cm rails and two 20cm rails. I may ad a lens support and a way to mount the setup...

A camera dolly and rail system that can support a dSLR or other video gear. The system uses 608 series "skateboard" ball bearings and standard hardware found at any home improvement store. Rails and legs can be made out of any 1" OD tubing or pipe...

Since I didn't have a way to mount the required focus and zoom motors, or even a way to attach the camera to the rig at all, I made a complete camera platform 100% 3D printed. I looked on this site for anything that would work that someone else had...

Since I didn't have a way to mount the required focus and zoom motors, or even a way to attach the camera to the rig at all, I made a complete camera platform 100% 3D printed. I looked on this site for anything that would work that someone else had...

I made a narrow versions of the tubeholder and modified the tripod flange to accept a 1/4-20 insert and ridge to attach a specific camera mounting plate. ... The parts I used to complete my camera mount system: 1/4-20 Threaded Inserts (better than the...

A camera rail for usage in an IKEA Lack Enclosure. The rail is attached with M4 wood screws to a leg of the table. The slider is steplessly adjustable with a M3 screw. The camera is attached to the slider with cable ties. The adapter is desgined to...

Crude first version of a gear system to motorize this camera rail: https://geni.us/xP6sHThe gears are currently simply press-fit. ...I encourage anyone to improve on the design!Works great with Applied Procrastinations control PCB:...

A camera rail for usage in an IKEA Lack Enclosure. The rail is attached with M4 wood screws to a leg of the table. The slider is steplessly adjustable with a M3 screw. The camera is attached to the slider with cable ties. The adapter is desgined to...

Improved design for the Articulating Camera Rail Arm. The original design used some remix parts that I was just not satisfied with. So I went to the drawing board and came up with this design. It allows for just about as much adjustment as you could...

Lightly sand as needed to personal preference for frictional fit in both rail and camera rails.

RasberryPi case with camera module bracket mount.

I Remixed the original Design to fit a standart 30x30mm Camera.

IPhone 11 mobile phone holder used to aid in video production for YouTube and other related video content. I would also recommend using solid polymer bearings for a smoother experience. ...

in progress.... ... 2x 20mm ( steel or aluminium ) pipe 6x f684zz bearing 1x 20 Teeth 5mm GT2 Timing Belt Pulley 2x GT2 5mm Bore Toothless Timing Belt Idler 1x GT2 5mm / 20 Teeth Timing pulley 1x Nema 17 Step Motor

Eufy camera crib rail mount

This camera rail-mount / holder allows you to change the height and Z-axis rotation of your camera. Using the joint on the camera you can also change its pitch. The rail can be mounted vertically on the leg of the enclosure. You can mount the slider...

This camera rail-mount / holder allows you to change the height and Z-axis rotation of your camera. Using the joint on the camera you can also change its pitch. The rail can be mounted vertically on the leg/side of the enclosure. You can mount the...

The lens support and camera quick attach modules are from this awesome thing: https://www.thingiverse.com/thing:1860391 15mm camera rail tubes are available on Amazon or elsewhere pretty cheap. ...I use aluminum as the carbon fiber ones split and shed...

This camera rail-mount / holder allows you to change the height and Z-axis rotation of your camera. Using the joint on the camera you can also change its pitch. ...The rail can be mounted vertically on the leg/side of the enclosure. You can mount the...

I wanted a way to attach a USB camera to my Ender 3 V2 that would not require screws. The unit simply hangs off the lower left rail. ...It could be remixed to raise maybe a bit higher.

**Additional Parts Needed** 2 - M3x15mm screws 2 - M3 nuts This is a mashup of the following things: [Microphone stand (tripod mount)](https://www.thingiverse.com/thing:1496504) [Raspberry Pi Cam Rail Mount for Ender 5...

The loop fits nicely with this pi cam, and likely many others as well: https://www.thingiverse.com/thing:1718628 I included my logo on the rail cover for fun, but also a clean unbranded one. Feel free to get creative and enhance or adapt as you...

The loop fits nicely with this pi cam, and likely many others as well: https://www.thingiverse.com/thing:1718628 I included my logo on the rail cover for fun, but also a clean unbranded one. Feel free to get creative and enhance or adapt as you...

The loop fits nicely with this pi cam, and likely many others as well: https://www.thingiverse.com/thing:1718628I included my logo on the rail cover for fun, but also a clean unbranded one.Feel free to get creative and enhance or adapt as you...

... a green background and was printed on the Makergear Prusa. More info on all kinds of camera related stuff at DSLRFILMNOOB.com Instructions Print it out, add a handle, square nuts, and thumb screws. ...Attach it to your camera rig and start filming.

You will need 4 of these to fit two rails to the bottom of the Tarot 680Pro, and for each you will need a bulkhead 12mm rubber grommet (see picture for full measurements), and two M3 nut and bolts. Can be used side by side with original hooks if...

This is a little piece I printed for my Nikon p1000 to cover the top rail from dust and prolong its life. it slots in nicely and has a rounded top. ...May fit other cameras as well