celestron tripod mount 3d models
354536 3d models found related to celestron tripod mount.thingiverse
I have a Celestron Spotting telescope, and a nice tripod, but it only has one anchor point, so the telescope has a bit of twist and wobble. I designed this adapter so I get a more stable mount. Be sure to print it upright, because you don't want...
thingiverse
Turn your Celestron CGX / CGXL tripod into an impressively heavy photographic tripod. Mount your camera, binoculars, or telescope to this stable, vibration-resistant platform. Parts List: - Tripod Head: available from Amazon or 3D print...
thingiverse
Fits a Celestron AVX tripod that has 2 inch diameter legs that are slanted 32.5 degrees from the vertical with accessory tray/spreader installed and tightened. 1/4" threaded insert on the shelf support is for securing the shelf. 6mm bolts in the...
cults3d
Created a dovetail mount for a Star Adventurer to fit onto a Celestron Tripod.
thingiverse
Created a dovetail mount for a Star Adventurer to fit onto a Celestron Tripod.
cgstudio
Sky-Watcher 120ED Telescope with Celestron Equatorial Mount Tripod is a high quality, photo real model that will enhance detail and realism to any of your rendering projects. The model has a fully textured, detailed design that allows for close-up...
thingiverse
Made for the Celestron 114 LCM model telescope, but might fit other tripods. Instructions: -------------- -Print holster -Clip on tripod leg -Insert cap -Enjoy! ... Check out my [other designs](https://www.thingiverse.com/TrustDavid/designs) for...
thingiverse
I designed this to pring without supports, and came out well on my Prusa MK3S Update: I started to find having to pop off the battery and move it to another leg of the tripod annoying on the rare occasions that I would slew my telescope around 180...
thingiverse
Clip to keep Celestron tripod legs togather, in various manners. ...
pinshape
this is an ABS replacement arm for the celestron telescope tripod spreader
thingiverse
Replacement arm for the tripod on the Celestron 130 Series of Telescopes - may fit other models.
thingiverse
I have a Celestron Evolution mount for my 8" SCT and the original rubber tipped feet were getting damaged after a few uses. I wanted to replace the feet with something a bit more robust. Using heavy duty tripod feet was an obvious choice and these...
thingiverse
This is a part acessory for a Celestron Powerseeker 70az Telescope Tripod. I have printed it in 20% infill with supports. Print 3 supports for each base. ...
thingiverse
This is a holder for the 38mm legs on a Celestron tripod. It basically snaps on and keeps them from opening up during transport. I printed in PETG for strength and heat resistance, but you could probably do in PLA as well. I would use a...
thingiverse
I made this remix of LKLyon clamps as the originals were too narrow for the leg spreaders on my 102GT tripod. ...I beefed up the leg clamps and opened them up to fit my spreaders
thingiverse
This is a tripod adapter for a Celestron Nexstar altaz goto telescope mount that I picked up used for cheap. ... This requires just two pieces of hardware, just a quarter inch screw to connect to the mount, and a 3/4" t-nut to allow it to screw to a...
thingiverse
This adapter allows to use an Celestron Cometron or Firstscope with an old Vanguard VTP tripod. ... The support was based on this design https://www.thingiverse.com/thing:353135 and the tripod plate is based on mesurements taken from the original tripo...
cults3d
This adapter allows to use an Celestron Cometron or Firstscope with an old Vanguard VTP tripod. ... The support was based on this design https://www.thingiverse.com/thing:353135 and the tripod plate is based on mesurements taken from the original tripo...
thingiverse
This is a remix of a tripod adapter for a Celestron telescope originally made by adafruit. My tripod (a targus TGT-58TR) didn't work with the adapter plate in that, so I modified the adapter top from that project and just made it one piece since I...
thingiverse
After the center piece of my Celestron NexStar 127SLT tripod cracked a few times I tried to look for a replacement piece. With no success, and after a few slight revisions, I came up with this bracket to help hold everything together. Hardware...
cults3d
replacement bracket for the leg for my Celestron PowerSeeker 114AZ. ...fit snug on mine could increase 1% to have a looser fit.
thingiverse
replacement bracket for the leg for my Celestron PowerSeeker 114AZ. ...fit snug on mine could increase 1% to have a looser fit.
thingiverse
... by sirhc. ...I needed a bigger "box" clip for the tripod that would be able to fit my projected box that houses a Arduino mega + ramps board. Before I went to print I used netfabb stl repair and sliced with prusasclicer. ... Remixed with Tinkercad
thingiverse
my 3d printed bracket to hold the synscan unit on a standard Celestron eq3_2 tripod https://youtu.be/Vdawy2VJQGA
thingiverse
Hello, This part is an Brace Arm for Celestron Astromaster 130 Tripod. ...I made this piece myself because mine broke.
thingiverse
Celestron CGX is a great mount, I love it. But there a few tiny details, which can be annoying over time. For instance, only 2 two AUX ports are not enough for many Celestron accessories (Hand Controller, WIFI Skyportal, StartSense, GPS Module...).
thingiverse
Adapter of the Celestron Firstscope for the Rollei tripod. .f3d file included for any adjustments. ...Remember to rotate the object 90 degrees first before printing.
thingiverse
These are customized "Smooth n' Curvy" knobs designed for mounting my Celestron 8" GPS telescope to its tripod. They use 3" long 3/8" bolts, leaving 1" protruding from the knob. Depending on your printers dimensional accuracy, you may have to ream...