coin sorter 3d models
25175 3d models found related to coin sorter.grabcad
Coin sorter for Kazakh tenge.All details from sheet plasticneed to finish the bunker
thingiverse
... ...Edit it online https://www.tinkercad.com/things/00X7aSHZUpL I created a coin sorter that would help me organize coins I has laying around. ...It is not too wide so I found it perfect to be placed in an area that wouldn't use a lot of space.
thingiverse
This coin sorter is loose change's worst enemy. Watch your pennies, dimes, nickels, and quarters spiral toward perfect organization. ... Print Settings Printer Brand: MakerBot ...
thingiverse
Stackable coin sorter. Each level sorts out a specific type of U.S. coin, so you can print only the levels you need. Just stack from smallest coin on the bottom to largest on the top, add coins to the top, and shake! Each level is numbered from...
grabcad
Landstown High School Governor’s STEM & Technology AcademyAdvising Instructor - Jennifer Renne My submission to the Extreme Redesign Challenge is a two piece coin sorter. This device gives someone the means to effectively and inexpensively...
pinshape
A Simple Coin Sorter made with measurements from the US Mint coin records. Some coins may enter various slots due to this not being tested and only using logical thinking to devise how everything works, not experimenting / testing / using...
thingiverse
This coin sorter was inspired by a cardboard one I saw on youtube by Mini Gear. I used this gear box by Sbrunel. www.thingiverse.com/thing:340727 and I used these coin counters by jfn302. www.thingiverse.com/thing:2460653 I made this with a hand...
thingiverse
http://www.thingiverse.com/apps/customizer/run?thing_id=2214061 Instructions Using the following options: coin_1_thickness = 2.15 coin_9_thickness = 0 coin_5_diameter = 0 coin_8_thickness = 0 coin_6_diameter = 0 coin_10_diameter = 0 coin_2_diameter =...
thingiverse
http://www.thingiverse.com/apps/customizer/run?thing_id=499177 Instructions Using the following options: image = 0 coin_7_diameter = 0 coin_2_diameter = 26.50 coin_1_diameter = 30.61 coin_6_thickness = 0 coin_5_diameter = 0 coin_4_thickness = 1.95...
thingiverse
http://www.thingiverse.com/apps/customizer/run?thing_id=2214061 Instructions Using the following options: coin_5_thickness = 0 coin_1_thickness = 2.15 coin_4_thickness = 1.95 coin_4_diameter = 21.21 coin_3_diameter = 24.26 understand = 1...
thingiverse
http://www.thingiverse.com/apps/customizer/run?thing_id=499177 Instructions Using the following options: currency = usd coin_4_thickness = 1.95 coin_10_diameter = 0 coin_8_thickness = 0 coin_3_thickness = 1.75 pattern = no coin_7_diameter = 0...
thingiverse
http://www.thingiverse.com/apps/customizer/run?thing_id=499177 Instructions Using the following options: coin_8_diameter = 0 height = 50 coin_1_diameter = 30.61 coin_5_thickness = 0 currency = usd pattern = no coin_4_diameter = 21.21 image = 0...
thingiverse
It is just a coin holder, for keep the coins organized, it is ideal for a shelve or a rack. I printed it and works fine. ... There are 4 model, two that are expandable and two that are not.
thingiverse
Needed a way to organize my mass of coins in my car. I just used commands strips to attach it to my cup holders. Intended for US coins. Might redesign with a lid on it to stop any falling out when I drive over a bump. Will need to rotate it so its...
thingiverse
... which I ended up removing it after it didn't print correctly. ...Other than that, it functions well, but sometimes the coins pop out of the slot incorrectly and it goes over into a different slot than it should but it works well most of the time.
thingiverse
The slots in the funnel are there so that you can hold on to either side of the coins and guide them down so that they don't land sideways or anything. The funnel will not go all the way into the connector however there is a hole in the bottom of...