coleman pool vacuum adapter 3d models

Reduced the thread diameter to fit the Bestway F4030 outlet on my coleman 18ft round pool based on the model from https://www.thingiverse.com/thing:2469017 designed by johannesathome. Include a 4.5mm of the threaded section for test fitting.

This adapter is inserted into the hose port on the pool and the clamp on the outside (over the hose) keeps it in place. The skimmer hose then just slides up over this. ...There is a ridge in the skimmer hose that mates with the ring around the coupler...

This adapter is inserted into the hose port on the pool and the clamp on the outside (over the hose) keeps it in place. The skimmer hose then just slides up over this. ...There is a ridge in the skimmer hose that mates with the ring around the coupler...

This adapter is inserted into the hose port on the pool and the clamp on the outside (over the hose) keeps it in place. The skimmer hose then just slides up over this. There is a ridge in the skimmer hose that mates with the ring around the coupler...

Pool vacuum adapter with use of the handle. ... compatible with YSAKI broom Allows you to complete the cleaning by connecting to the main filter.

I had a pool vacuum without a stick so I made this to be able to attach a basic paint roller extender stick.

Good for 1 1/4 pool vacuum hose. ...Adapter is for above ground intex coleman pools.

Note that if you have two outlets that run from the pool to the filter/pump (plus the third that runs back from the pump to the pool) then you need to either stop up the outlet that you don't have the printed adapter hooked to (which is what I have...

I realized an adapter to be able to connect my vacuum cleaner in 32mm to the intake of my swimming pool. ... I added the openscad file.

This adapter is to insert into the standard intex pool skimmer hose attachment. You can then attach your vacuum hose over the larger end of the adapter. I printed at 50% fill and slowed the print way down to make sure it came out smooth. This...

The adapter ends on my pool hose had degraded and were flaking apart. They also didn't fit my vacuum very well, so I designed a replacement. I printed this in PLA, which is probably not an ideal 'in the pool' material, but we don't have any other...

Сделал переходник под стандартный разъем шланга и малярную палку с резьбой. ... I made an adapter for a standard hose connector and a painting stick with a thread.

Adapter to attach 1-7/8" shop vacuum fittings to the pool hose for cleaning. ... Two versions of the clip included, have only tested one.

Adapter to attach 1-7/8" shop vacuum fittings to the pool hose for cleaning. ... Two versions of the clip included, have only tested one.

Adapter for tubular pool habitat and garden to connect a vacuum cleaner or hydraulic robot on the suction of the pump https://www.tiktok.com/@jh_3d/video/7121753762204536069?is_from_webapp=1&sender_device=pc&web_id=7070547989610006021

2.) There's no way to vacuum the bottom of the pool 3.) There's no way to skim water from the top. I've solved all these issues with 3D printing (and a new pump). Here's the vacuum adapter. The bulkhead fitting has a strainer built into it and...

I have an [OOGarden pool](https://www.oogarden.be/be/fr/prod-39959-Piscine-Cape-Town-2.html) and wanted to use an [Intex vacuum...

In order to connect the hose (32 mm inner diameter) of a pool vacuum cleaner to the water outlet fitting (goes to the pump). Tested with Intex pool and pump. ... The inner thread screws on the outer thread of the pool fitting where normally the grid...

The filter that comes with the vacuum doesn't do a very good job when cleaning the fine silt in the pool. Sooooo I design an adapter to use an ultra fine coffee bag and it work pretty well. If you can find a similar size bag with a higher micron...

The filter that comes with the vacuum doesn't do a very good job when cleaning the fine silt in the pool. Sooooo I design an adapter to use an ultra fine coffee bag and it work pretty well. If you can find a similar size bag with a higher micron...

The more expensive ones (or larger pump kits) come with 1.5 inch tubing and shut offs to make this more manageable (if you buy them extra) but for the stock 1000 pump and 1.25 inch tubing you get on the entry pools (mine is the 15 foot 48 inch pool)...

The more expensive ones (or larger pump kits) come with 1.5 inch tubing and shut offs to make this more manageable (if you buy them extra) but for the stock 1000 pump and 1.25 inch tubing you get on the entry pools (mine is the 15 foot 48 inch pool)...

Remix for this project to fit my Coleman 22ft pool. Should fit 18ft pool too. ...https://www.thingiverse.com/thing:4546629

The adapter that swivels and connects the pole to the vacuum head broke, and instead of ordering a whole new assembly, I decided to create my own part for replacement. The model turned out beautifully.   The OEM part has very thin walls (roughly...

The adapter that swivels and connects the pole to the vacuum head broke, and instead of ordering a whole new assembly, I decided to create my own part for replacement. The model turned out beautifully. The OEM part has very thin walls (roughly...

... net holder. ... Connections: * Large-hose shop vac attachments (I have a Ridgid) * Standard aluminum telescoping pool stick thing * Intex 1.25" hose Printed with PETG for resiliency but I don't think that matters much. ... Zero supports needed!

... by another designer who made a pool clip I decided to put my spin on it. ...My pool has more of an ellipse shape so I drew up the cad drawing and exported an stl. ...In the photos that are attached you will see the difference between the two clips.

I just got tired of unscrewing the skimmer every Saturday to hook up the pool vacuum. So here I have designed an adapter that only needs to be plugged onto the skimmer. It is made for the Intex pool vacuum cleaner and the Intex skimmer. Overall...

These adapters are meant to fit on an Aerobed Air Mattress Pump to inflate a Coleman Air Mattress.The inflate adapter has a flange to trigger the pump to turn on once seated with a push/twisting motion. I printed it at 100% infill using PLA for...

A simple (yet very effective) pool vacuum system. The project consists of 3 parts to be printed and a 1" hose to be bought at your local hardware store. The wand-slang connector fits into the suction port of your pool. The hose has a spiral on the...