cr 10 direct drive 3d models

CR-10 DirectDrive holder.

So I started to design a direct drive system to move the extruder stepper above the hot end and limit my bowden tub to less than an inch. Though I have pretty much replaced all of the printer's original extruder and hot end parts, I wanted this to...

This is modified Direct Drive for CR-10 or CR-10S printer Modified: - reinforced plate for directDrive (v 3.1)

https://www.thingiverse.com/thing:2869640 Another direct drive mount I'm working on, still haven't decided just what direction I want to go. I have a MK8 aluminum extruder on the way so I'll double check measurements. That fang in the picture is...

I use the direct drive kits found at https://printermods.com/ Although I love the upgrade from a Boden, I am not crazy about putting so much weight on a moving carriage with an unsupported frame such as a CR-10. I definitely do not want to mount...

.STLs do not come in best print orientation This is a direct drive conversion bracket for the Creality CR-10 printers. It allows for the direct attachment of a stepper motor onto the existing red aluminum X carriage bracket. This design also includes...

After converting from bowden to direct drive I needed to keep my cables from getting pinched or drooping onto the back side of the build platform. Its designed to snap over the extruder drive motor with the tang to the back. ...I used a zip-tie through...

Took inspirations from two other Thingiverse CR-10 Direct Drive mounts and combined then to fit my needs.

Yeah, its Cr-10 direct drive motor plate. 100% working and no sacrifice from build plate size. I print E-sun elastic with it and no problems, only thing that you probably need to adjust extrusion multiplier to 2.00 in simplify 3d. ...OEM fang fits...

CR 10 Direct Drive Extruder Mod Single Part, remixed from another 2 part design. The Extruder is still not centered over the print head but it's a lot closer than the version this was remixed from. ... Watch the dual fan setup on the far side of...

I began with the CR-10 flexible Filament Extruder by darkytoothpaste ( , CR-10 flexible filament extruder bracket with adjustable spring tension found on #Thingiverse https://www.thingiverse.com/thing:2604471) then I found s_gutz's direct drive...

This is a very stable and stiff mount for Direct Drive on a CR-10 and alike. I have taken the great work of Magnus Hansson and adapted it to my printer. It uses 2 carriages for the X axis.Its made for the Orion bed...

Cable chain mounts for X Endstop and Bondtech Direct Drive for Creality (Cr-10 / Ender) printers Uses this cable chain: https://www.thingiverse.com/thing:2920060

This is the 2nd version of my direct drive extruder mount for the CR-10 (here is the original version: https://www.thingiverse.com/thing:3755269). It combines a Bondtech dual drive geared extruder with an E3D V6 hotend into a direct drive extruder...

I enjoyed the original design due to its versatility but would really have liked to see a direct drive version of it. Design is still a work in progress! Files, plans and instructions subject to change. Most of the parts can be salvaged from the...

This is my (bad) clone of the great Bullseye fan duct for the Ender 3/CR-10, for use with direct drive extruders which place the extruder stepper directly above the hotend parallel with the Y axis. If you've tried to fit a Bullseye duct to a direct...

* sufficient tinkering experience (this one isn't a no-brainer obviously) Personally, I think the CR-10 should have been a direct drive printer in the first place. It's so much more convenient than fiddling around with that bowden tube. Plus, the...

11- Enjoy your Direct Drive Ender 3 / Ender 3 Pro / CR-10. Don't forget to change your slicer settings and reduce the retraction to 1mm or lower. For some filaments (mostly PETG) I used 1.4mm as well because of the strings. I also recommend...

This goes into the M10 0.9mm threaded fitting place on the CR-10 hot end heat sink, and allows the use of some direct drive feeders. There are two variations, each with & without support. You need to cut the teflon tube at the heatsink entry,...

Also added jig to reposition stepper, as the Creality direct drive converter bracket positions the stepper 15 mm higher than it needs to be. Bolt the jig to the bracket using the center holes on both sides, then drill out the bracket using the...

This a companion thing to my direct drive extruder bracket - https://www.thingiverse.com/thing:3589452 One of the drawbacks of a direct drive system, when the spool is mounted on the top cross bar of the machine, is that tension from the extruder...

A custom design for Bondtech Dual Drive to mount directly on the E3D V6 hotend. I wanted to design a mount what use nuts for the assemly to avoid any problem and the extruder is directly mounted on the hotend so there can't be any problem with the...

A custom design for Bondtech Dual Drive to mount directly on the E3D V6 hotend. I wanted to design a mount what use nuts for the assemly to avoid any problem and the extruder is directly mounted on the hotend so there can't be any problem with the...

A custom design for Bondtech Dual Drive to mount directly on the E3D V6 hotend. I wanted to design a mount what use nuts for the assemly to avoid any problem and the extruder is directly mounted on the hotend so there can't be any problem with the...

https://i.postimg.cc/4fY9bnt9/Direct-Drive-Extruder-Installation-manual.jpg * Added V2 model with 2 M3 Screw Holes so you can design your own attachment adapter for BL-Touch and etc'. I recommend using my Spring Feet design to silent the printed...

The hole in the direct drive mount is for a 20x20 heatsink on the stepper, by the way, I forgot to mention that. Added MKIII-BowdenIn file. Should be able to thread a 5mm pushlok into it, made hole 4.78mm. Update 2/28: Printed out the MKIII Bowden...

This is a mashup of: This Fang-compatible BLTouch mount: https://www.thingiverse.com/thing:2994381 This CR-10 Direct-drive mod: https://www.thingiverse.com/thing:2869640 The whole arrangement is compatible with this Tacblades high-clearance fang...

Con él se convierte la impresora en "direct drive" eliminando el alimentador "Bowden" y preparandola para filamentos flexibles tipo TPU o Filaflex. Diseñado para una impresión sin soportes. Son dos versiones. Una con soporte para el sensor de falta...

Description -------------------------- I am proud to introduce a brand new take on a direct drive extruder conversion for the Creality CR-10 which requires no additional parts and uses nearly all of the stock components. I designed this because...

... will be at the exact same height wether you use V6 or Volcano! I also included a mount for the probe that comes stock with the CR-10, it also mounts onto the same spot as the hotend mount mounts to the printer frame! ... Prints with no support!