creality cr 10 v2 upgrades 3d models

Ender 10S Upgrade Power Supply Control Unit Stand Best Creality CR-10/S/V2 Upgrades & Mods elevates the control unit about 2.8 inch - 7.3 cm helps in good unit ventilation and better cooling easier access to the sd card avoid grounding electric...

I´ve constructed an upgrade for the bad filament holder of the Creality CR 10 2. The distance between the ball bearings can be adjusted with a crank. The main holder is fastened with a large nut. Use two ball bearings with the following dimensions:...

- E3D Clone Heater Block Replacement for CR-10 (early version) stock heater block https://macewen3d.com/collections/upgrades-for-cr-10/products/e3d-clone-heater-block-replacement-for-cr-10-stock-heater-block - Creality CR-10 Hotend Threaded Heatsink...

Filament sensor mount for the Creality CR-10 V2.

This is a model of Creality's heatbreak for the CR-10 V2/V3. I suppose you could print this, but my intention of sharing is for it to be used as an aid for designing modifications for the CR-10 V2/V3. ...STL and Step file included.</p>

Support for raising the 125 mm wide main block of Creality CR 10 3D printers and derivatives.

... to hold your cable in place. ...(No more messy cables!) It clips tightly onto the base frame of a Creality CR-10 V2 while allowing minimal cable motion along the in one direction. ... Compatible with other 3D printers that have the same 20x40mm v-slot.

I created this model to use for attachements to the creality cr-10 v2 box, this is a very accurate model. I invite anyone to add additional details to this. ... I have not completed the holes on the back of the controller or any of the components...

Adaptador para la impresora CR-10 v2 de Creality. Con él se convierte la impresora en "direct drive" eliminando el alimentador "Bowden" y preparandola para filamentos flexibles tipo TPU o Filaflex. Diseñado para una impresión sin soportes. Son dos...

You can't find your Tools? ...Workspace looks messy?! NO PROBLEMO!!! It's a Toolholder for Creality CR-10 Printer. ...Probably compatible with other 3D-Printer, its very standard designed.

This is not really a remix of the [cable holder](https://www.thingiverse.com/thing:4529886), (which looks exactly like the stock clip delivered by Creality with the CR-10 V2), but a new design. I wanted to cover the V-slots of the frame (at least the...

Dangling calbes of the Creality CR-10 printers have always been a problem, especially the bed heating cable was always likely to get stuck at the corner of the bottom frame. Therefore I had alredy created a corner slide (simply replacing the 20x20...

... to have the top on even when printing pla/petg so made these spacers. They are made to vent out some hot air to not mess up pla prints. I have a high temp cr-5 pro h machine. This is a simple print. ... Read text on hotend kit on how i printed.

Creality CR-10 Upgrade Suite. This kit includes an extruder with improved ergonomics and functionality as well as an improved bed level adjustment system. ***New as of 1-25-18 is the inclusion of a E3D-V6 hot-end adapter. This adapter places...

For the upgrade i made some parts that you can easily mount the Laser to the Cr-10. With this solution you have the opportunity to mount the Laser at the Printing head, or put it away to a second bracket, that is mounted at the frame of the Cr-10. I...

Parts for better airflow when changing out fans on the CR-10. ... Read more about the designs and how to install them here: https://fdproj.wordpress.com/2018/01/22/cr-10-silent-new-fans-vibration-dampers-and-design-upgrades/

This is a ventilated cover for the power supply to the Creality CR-10 V2

Creality CR-10 Hotend

This is an adapter plate to mount the stock Creality CR-10 V2 or V3 fan and hotend to the Wham Bam Systems MUTANT.

Mount for BL-Touch on a Creality CR 10 V2 Printer. The strengthening is in the same angle like the strengthening for the whole Printer. Unnecessary middle hole for the Bl-Touch removed. ... Enjoy printing :-)

Mount for BL-Touch on a Creality CR 10 V2 Printer. The strengthening is in the same angle like the strengthening for the whole Printer. Unnecessary middle hole for the Bl-Touch removed. ... Enjoy printing :-)

Based on the design from Pestkowiec, this is a remix that works with the Creality CR-10 V2 / V3 3D printers. I used M5 x 10mm bolts with M5 t-nuts to secure the feet to the 2040 extrusion frames. "t3dhlefttallsbfv2" is the stretched out version...

I really liked the Filler creation by HugoHuge: https://www.thingiverse.com/thing:3020026 But I needed an angled adapter for my Creality CR-10 V2 and found DasMani01's, which is great! : https://www.thingiverse.com/thing:4333402 However, I...

Рекомендую использовать с креплением под директ: https://www.thingiverse.com/thing:4491805 Smooth fang mount for the Creality CR-10 V2 + 40mm fan duct. ...</b> <b>Compatible with:</b> https://www.thingiverse.com/thing:4389912 ...

summary is this is a useful little spacer for the creality cr-10

Made this because I ran the nozzle into the bed a few times and for the life of me I could not find documentation or any blurb on the web of what direction to turn the knob on my Creality CR-10 V2 to make the Z axis (or Zed depending on what side of...

... for the filament feeder. Be sure to align the pulley with the entrance to the filament sensor. I used a 608 ZZ skateboard bearing in the pulley.Version in photo was printed on Creality CR-10 v2 with generic PLA, 0.4mm nozzle, 0.2mm layer height.

I made this to mount my Nest Home Outdoors camera to my Creality CR-10 V2 printer so I could monitor prints and create time lapse of the prints. If you would like to use the bracket then you will need two 2020 extrusion corner brackets, four m5 x .8...

I made this because I ran the nozzle into the bed a few times and for the life of me I could not find documentation or any blurb on the web of what direction to turn the knob on my Creality CR-10 V2 to make the Z axis (or Zed depending on what side...

*please slot in a short PTFE tube into Feeder V3 *** User B*** If you printed my V1 before, just print everything except the "Bracket", then swap them Where to get Creality CR-10...