deep space 9 model

A remix of this: https://www.thingiverse.com/thing:2152176 You probably should add supports around the top center cap "antennas" of which there are 3. ... The pylons might print without support but I used some.

Deep Space 9

Deep Space 9 a very complicated 3D-Model Support is possible necessary

This model has a diameter of 12 cm, and can be printed in 2 versions: the full piece: Deep_Space_9.stl in two fitting halves: Deep_space_4.stl and Deep_Space_5.stl Print Settings Printer Brand: Up! Printer: Up Plus2 Rafts: Yes Supports: Yes...

This model has a diameter of 12 cm, and can be printed in 2 versions: the full piece: Deep_Space_9.stl in two fitting halves: Deep_space_4.stl and Deep_Space_5.stl Print Settings Printer Brand: Up! Printer: Up Plus2 Rafts: Yes Supports: Yes...

A Small Model of DS9. ...Meant for use in Star Trek Ascendancy.

This model is an upgrade from 2-3 years ago,After the drawing, I printed this model 3Dthe whole contains about 70 parts, the outer circle is 350 mmand the height 400 mm it can rotate manually on its bottom brass shaftthere are 2 bearings for this in...

Small scale low poly model of Deep Space 9, scaled at 65mm across. ...Optimized to be printed in two halves, though supports will still be needed for the pylons.

EDIT: added a version with the notch for a small alignment pin and the pin itself, i haven't actually printed this one The base model i made for the Deep Space 9 LED lamp, in case somebody likes the structure but not cutting and soldering led strips....

... alignment pin and the pin itself. ...I haven't actually printed it, feedback is welcome The base model i made for the Deep Space 9 LED lamp, in case somebody likes the structure but not cutting and soldering led strips I printed at 0.12 with supports

... pin and the pin itself. ...I haven't actually printed this one, feedback is welcome The base model i made for the Deep Space 9 LED lamp, in case somebody likes the structure but not cutting and soldering led strips.I printed at 0.12 with supports

The R-9 Deep Space Shuttle is an FTL-capable long-term exploration and research craft, primarily used to study and gather samples of alien life-forms. Several hundred meters long, the shuttle is capable of transporting large quantities of live cargo,...

A card kit of Deep Space 9. Kit holds together with tension and a little glue If you decide to print as separate pieces, please print 6 struts, 3 deflectors, and 3 pylons. Would love to see your makes! Instructions: We want to start...

Candlestick starcraft pylon Deep space 9 ds9

A simple 9" combat gauge primarily for measuring for deep striking distance in Warhammer 40k games, I have included a Space Wolf emblem because they are simply the best :p

... ...Lucky us, right? I did not make this; this is only a conversion I did of MeslesitsFleetYards original model from a .max to a .stl file for printing. ...Find this model and more here on his Deviantart page: http://metlesitsfleetyards.deviantart.com/

Conversion of MeslesitsFleetYards original model from a .max to a .stl file for printing. ...Scaled to 1:2000 Find this model and more here on his Deviantart page: http://metlesitsfleetyards.deviantart.com/

Model dimensions: - height – 151.3 mm - width – 107 mm - thickness – 37.5 mm Model consists of parts: body bottom part, body middle part, body upper part, bottom front left insert, bottom front right insert, bottom rear left insert, bottom rear right...

I used DS9 model made by nd4spd1919, scaled it and cut it in half. Then I laser cut clock shield, added clock mechanism and glued DS9 on top. When engraving, use clear acrylic/perspex and don't take cover off. After engraving paint the engraved...

I used DS9 model made by nd4spd1919, scaled it and cut it in half. Then I laser cut clock shield, added clock mechanism and glued DS9 on top. When engraving, use clear acrylic/perspex and don't take cover off. After engraving paint the engraved...

A deep space explorer to reach the outbounds of the galaxy.The model was made in Lightwave and textured with substance designer. It is textured with 12 sets of 1K or 1024*512 maps including diffuse/normal/specular/emissive when needed Mapped on a...

Deep space transport craft created in 3Ds Max, with animated solar panels, no textures applied. ... 3D Studio (.3ds) Cinema 4D (.c4d) Autodesk FBX (.fbx) OBJ (.obj) 3D Studio Max 2014 (.max) Renderer: V-Ray 3

So basically I had built a very similar model to this when I was a kid. It was a kit-bash. Yes I was influenced by the Black Hole movie but as you can see it is different. The parts were started using a space 1999 eagle. There is a sci fi...

THIS IS MODEL OFDEEP SPACEJET AND CAN BE USED FOR DEEPSPACE MISSIONS TEXTURES AND BACK GROUNG IMAGES INCLUDED

space deep

Small scale model of Deep Space 9 customized as a spinner for the top of the MP Mini Select/Malyan, though I'm sure it would fit other machines. ...Optimized to be printed in two halves, but still needs supports for the pylons.

... drivel. I did not make this; this is only a conversion I did of MeslesitsFleetYards original model from a .max to a .stl file for printing. ...Find this model and more here on his Deviantart page: http://metlesitsfleetyards.deviantart.com/

... for your heart. ...I did not make this; this is only a conversion I did of MeslesitsFleetYards original model from a .max to a .stl file for printing. ...Find this model and more here on his Deviantart page: http://metlesitsfleetyards.deviantart.com/

... the wormhole! I did not make this; this is only a conversion I did of MeslesitsFleetYards original model from a .max to a .stl file for printing. ...Find this model and more here on his Deviantart page: http://metlesitsfleetyards.deviantart.com/

Model dimensions: - length – 482 mm - height – 217.3 mm - width – 60 mm Model consists of parts: body part 1, body part 2, body part 3, front grip, front insert, grip, handle, left plate insert 1, left plate insert 2, left side insert 1, left side...