dewalt tough system to tstak adapter 3d models

This is an adapter that allows the DeWalt T-Lok system to latch onto the DeWalt Tough System

This is a adapter to allow someone install a removable work top onto a Dewalt Tstak. I used a butcher block top from home depot, and cut it down to size. I printed these in armadillo filament from ninjatek. I thought the flexibility and durability...

This is the feet for the Dewalt tough-system radio. ...I printed in TPU

More to come this is the first one I did fits in the bottom of the large trays to split them in to 2 smaller compartments I likes the tray for the upper half and thought it would be nice to split the lower ones as I have lots of small screws this...

... tape between box and part. Also put biggest washers as you can from both sides of rivets. Part was optimised to not crack after applying the rivets. Use M4 bolts if you want to be sure. ... Holds nice you can lift multiple TStak boxes with it.

Made to fit in the [Dewalt Tough System 2.0 6-Compartment Small Parts Organizer](https://www.homedepot.com/p/DEWALT-Tough-System-2-0-6-Compartment-Small-Parts-Organizer-DWST08020/313818239).

This is a nesting box for the Dewalt Tough System box. It is ever so slightly smaller so it doesn't get stuck. ...The single divider gives you something to grab on to.

Made to fit in the [Dewalt Tough System 2.0 6-Compartment Small Parts Organizer](https://www.homedepot.com/p/DEWALT-Tough-System-2-0-6-Compartment-Small-Parts-Organizer-DWST08020/313818239). ... Included are STLs for nesting cups with 1, 2, and 4...

I made these to fit in the Dewalt Tough System organizer cups. The stock cups nest in each other and have little ledges to keep them from inserting too far. This is perfect for allowing smaller cups to fit inside and take advantage of any extra space...

Tstak adapter. ...To be reveted on whatever you want to tstak but Tstak 2 drawer. It doesn’t work on the tstak 2 drawer and it might not work on other toolboxes. ...

Remixed to match the rounded part that allows the latch to snap. ... Original part resembled the Tough System latch despite being labeled as a TSTAK latch. Print with flat side on bottom. ... No supports needed.

Dewalt Tool insert for Tstak (Thingverse problems in generating stls previews) i upload the original file DWG to make easy if you want to modify the layout.

Dewalt Tool insert for Tstak (Thingverse problems in generating stls previews) i upload the original file DWG to make easy if you want to modify the layout.

Mounting for DeWalt Tstak Chests, Maybe u need some Spacers Extra because its not so easy to redesign the whole thing to fit... ... I Also Redesigned the Clip a litte bit to Fit an M4 hex nut to use Screws

These are bins designed to fit in Dewalt Tstak or Craftsman VersaStak drawer units. Theyre sized to hold 30+ res/com key blanks. ... Assuming you're going to print a lot of them, use vase mode for quick printing.

A 3D printable replacement latch for DeWalt TSTAK toolboxes. Print with supports to allow the pins to be printed. ...We produced it out of PETG and it fits well and latches nicely.

Fits DeWalt ToughSystem 2.0 Half-Size Organizer DWST08020. ...

**They WILL NOT work with the Tough System organizer bins.** These cups aren't exactly a remix of the [DeWalt Tough System Organizer Nested Cups](https://www.thingiverse.com/thing:2976211) by Brandito. Those organizers inspired my [Milwaukee Packout...

Created an adapter between Dewalt DCV586MN and Dyson V8 so I can use Dyson accessories on my Dewalt vacuum. ... I printed with support, did not test without.

this model allows dewalt batteries to fit on festool power tools

I wanted to be able to use my Tough Case the same way - hence this plate. ... It is designed to take the exact same pegs as the Milwaukee Packout - recreated [HERE](https://www.thingiverse.com/thing:5479915 "Milwaukee Packout Modular Oscillating...

... not enough room for the discs to fall out of the holder when the lid is closed. The holder fits in the compartment where the charger would sit, leaving the battery copartments free. Will probably fit other DeWalt 125mm anglegrinder TSTAK cases.

Nesting cups for the DeWalt TSTAK clear top organiser, these suit the larger cups. There are some similar designs already available online but I found the fitment not quite right for my liking so it sent me to design my own. ...Enjoy!

I managed to break a clip to the drawer on a TSTAK IV, so I designed a new one.

This allows me to secure my drill box on top of a Tstak Toolbox stack which makes it easy to carry around with the toolbox. It might be useful for someone else - who knows? ... Use plenty of shells for rigidity.

This allows me to secure my drill box on top of a Tstak Toolbox stack which makes it easy to carry around with the toolbox. It might be useful for someone else - who knows? ... Use plenty of shells for rigidity.

As soon as I saw the DeWalt TSTAK double drawers I knew those were for me and I was lucky enough to run across latifimr's organizers for these drawers. I printed a coupe of them out but was unhappy with the longer print times because of the nice...

If you'd like to design an adapter for something else, I've uploaded a file with just the camera end of the thing. Print Settings Printer Brand: RepRap ...

Connects between DeWalt sander adapter (purchased part) to DeWalt shopvac

These nested cups are designed to fit in both the small and large bins from the Dewalt TSTAK Shallow organizer, the Stanley FATMAX Shallow. Should fit in the Craftsman Versastack organizer (UNTESTED). They WILL NOT work with the Tough System...