diatone r349 3d models
1778 3d models found related to diatone r349.thingiverse
Diatone R349 R369 Motor Protector For 20xx 22xx motors
thingiverse
I designed these brackets that cover the motor wires on the Diatone R349. They just snap on to each arm. FYI, the arms are a bit wider near the body, as opposed to near the motor. It's easier to snap them on closer to the motor, and the slide them...
thingiverse
A simple bracket to mount LEDs to for a Diatone R349. The bracket connects to the two rear posts that hold the canopy on. If the holes are too tight, just drill out or print at 100.02%. ... The LEDs I purchased are these: ...
thingiverse
Hello, this is my RX antenna mount for the Diatone R349 which comes into the hole an the end of the canopy. You need to drill a bigger hole do insert the antenna thru that hole for the Antenna Mount. It is a press fit, when done with TPU (95a). ...
thingiverse
Duct for R349, only need to remove the props to install. ... Screws not needed, can be installed with a ziptie.
thingiverse
Well my r-xsr was outside the diatone R349 with some straps so i just wanted something to hold it in place and protect it. ...Just remove the canopy and place it in the standoffs and done.
thingiverse
This is a dji digital fpv conversion kit for the diatone r349; you'll need to: 1) Replace the default stack with the GEPRC toothpick 20A aio board (https://geprc.com/product/gep-20a-f4-aio/). Note that this board will be elevated so the motor leads...
thingiverse
A support for mounting [Armattan's Universal LEDs](https://www.rccrazed.com/accessories-leds-armattan-universal-led-p-313.html) on the R349. It replaces the stock plastic barrier that covers the capacitor. ... Must be printed in TPU: insert the LEDs...
cults3d
Shark fin for the Diatone R349 - Helps with turtle mode. Revision 2 is up - Bigger antenna mount for the Lollipop and AXII. ... R3 is up, minor antenna mount delete that should be more accommodating to other types of antennas.
thingiverse
Shark fin for the Diatone R349 - Helps with turtle mode. Revision 2 is up - Bigger antenna mount for the Lollipop and AXII. ... R3 is up, minor antenna mount delete that should be more accommodating to other types of antennas.
thingiverse
Diatone GT-R349 and similar battery protector\launchpad. In comparison to the thing it is remixed from (https://www.thingiverse.com/thing:2588938) it weights approximately nothing - 8 grams. Needs to be printed with supports. ... Fusion360 archive...
cults3d
Diatone's little 3 inch monster the GT R349 is an amazing craft and has a proven track record. It achieves astonishing speeds and all the acrobatics of a 5 inch. This craft comes in different configurations in cooperation with T-motor, Runcam and...
cults3d
Diatones canopy is slightly too small to accommodate the DJI Caddx VTX so this was designed to hold the new antenna and arch over the VTX. Large cutouts around the camera were necessary for prop clearance and yes it does kinda leave your expensive...
thingiverse
These are mounts for the bn180 GPS module on the diatone r349 rabbit 3" quadcopter. I have only tested the vertical mount, because it keeps the GPS closer to the frame and thus leaves it better protected. I made the horizontal mount in case anyone...
thingiverse
This is a BN-180 GPS Sensor mount that fits my Diatone R349 HD MK2. It holds the GPS very securely. I was able to zip tie my receiver (R9 MM) to the bottom of it, as well. Which is really nice to free up some space. I have not checked to see if that...
thingiverse
Quick and dirty mount for the Diatone R349 and Realacc UXII Stubby VTX Antenna. It's not intended to mount directly to the stand-offs at the back of the quad, but instead over top of the round canopy mount for the stand-offs. The antenna is also...
thingiverse
This is a BN-180 GPS Sensor mount that fits my Diatone R349 HD MK2. It holds the GPS very securely. I was able to zip tie my receiver (R9 MM) to the bottom of it, as well. Which is really nice to free up some space. I have not checked to see if...
thingiverse
Clean plate for diatone gt r349, compatible with umma85 and 95x parts.
thingiverse
This is a canopy for the Diatone GT-R349, longer on the front to avoid the propellers in the visual field. ...It can be printed both in TPU or PLA.
thingiverse
Original post_ Made this mount some time ago for my Diatone GT R349 micro drone. It's far enough from the bottom mounted battery and it doesn't touch the frame. Range for this kind of quad isn't an issue I think. Never had problems. Printed...
thingiverse
A super simple way to mount a caddx vista & DJI camera to the diatone rabbit R349; note that the original stack has been replaced with a geprc 20A aio flight controller. This 3d-printed components of this project consist of three-parts: 1) A...
cults3d
Diatone's little 3 inch monster the GT R349 is an amazing craft and has a proven track record. It achieves astonishing speeds and all the acrobatics of a 5 inch. With the Caddx Nebula v2 coming out, it was time to convert my favorite 3 inch to the...
thingiverse
This is a remix of another canopy found on thingiverse. I extended the antenna holder to squeeze-fit the UXii or Foxeer Lollipop. Just press it in, and it should stay in no glue required. ...If you like to crash a lot, consider a dab of hot glue inside...
thingiverse
... rabbit. You will get larger field of view and more crisp images without sacrifying your HD recording. ZX-RC warmachine canopy available for download. For more info and download: https://zx-rc.blog/2020/09/29/diatone-r349-r369-hd-canopy-upgrade/
cults3d
Used in Diatone GT R349 to hold battery wires, capacitor and antennas Check more details from this build at https://rotorbuilds.com/build/22688
thingiverse
Used in Diatone GT R349 to hold battery wires, capacitor and antennas Check more details from this build at https://rotorbuilds.com/build/22688
thingiverse
... small and simple to do the job. Link to the VTX Antenna Mount that I also made for the R349: https://www.thingiverse.com/thing:3317546 Link to the TBS Crossfire Antenna Mount that I also made for the R349: https://www.thingiverse.com/thing:3317512
prusaprinters
Since it has zip ties and now a Crossfire antenna holders it hard to level this thing so i just made something small and simple to do the job. Link to the VTX Antenna Mount that I also made for the R349: https://www.thingiverse.com/thing:3317546 Link...