durafly tundra v2 for sale 3d models

FPV deck for Durafly Tundra V2 and DJI airunit. Camera mount is made for Savox SH-0263MG servos. I printed this using polycarbonate, because it needs to withstand the heat of the airunit. ...PETG would work also.

Bonnet for Durafly Tundra (The little one)

A simple wall mount for the durafly tundra. ...Model was a bit too big for my place, so i put it on the wall

This is a replacement for the front section of the Durafly Tundra and Tundra V2, it does not allow for a bonnet and so will make your plane look significantly more ugly however it will act as a replacement after a crash. When putting it on the plane...

Mount for Matek plane FC's to put into the rear bay. Easy to lock with two M3 bolts. ... I use [Ruthex M3 threaded heat inserts](https://www.amazon.de/ruthex-Gewindeeinsatz-St%C3%BCck-Gewindebuchsen-Kunststoffteile/dp/B08BCRZZS3?th=1) there, so the...

Hard landing - broke my Durafly Tundra V2 gear screw cover. This is not a 1:1 copy of the original (i'm not a CAD guru :-) ... quick an dirty made with tinkercad) but it works ... ...

A remix of the Durafly Tundra Landing Gear Fairings by SaKes: https://www.thingiverse.com/thing:4360587 Similar in design and function to the original, adjusted the fairing geometry to sit higher/closer to the fuselage. Fairings are designed to be...

A remix of the Durafly Tundra Landing Gear Fairings by SaKes: https://www.thingiverse.com/thing:4360587 Similar in design and function to the original, adjusted the fairing geometry to sit higher/closer to the fuselage. Fairings are designed to be...

Some spats that clip on to the landing gear wires of the durafly tundra. Helps prevent the wires from bending on those less than perfect arrivals. ...Thers a top and bottom spat, easier to print than one long one, spreads the load a bit better can be...

Made these to replace broken brackets on my Tundra V2 (pretty sure its a V2). Original brackets are curved and these straight but they bend into place when you tighten the screws. I had to use screws a few mm longer than the stock screws to get...

Add 25% infill modifier a few mm to the top end for better top walls. Add 7 perimeters modifier to the lock part. Manually add supports to the upper part of the overhangs as shown in the screenshots. Use the spare magnet came with the plane...

... for an RC Airplane. ... Specifically designed for the Durafly Tundra. Uses 20mm velcro straps. Can either be screwed down with 3mm bolts or glued in place. ... The 100mm model is perfect for a 2200mah battery and the 150mm model is good for 5000mah.

Hanging hook for Durafly Tundra so you can hang up your plane on the ceiling. ... This mount will fit with Durafly Tundra universal wing mount: https://www.thingiverse.com/thing:4357646 Hanging hook are mounted by 2pcs M3x10 countersunk screws.

This is a basic pod suitable for holding a pan tilt camera unit on the Durafly Tundra.

Simple Transport Aid for the Durafly Tundra. Keeps it from rolling through your trunk. ... Should be loose fit.

These are wheels nuts for the Durafly Tundra. ...I modelled these from scratch and purposely made them larger than the originals to provide more support to the wheel.

Mounting for GoPro to Durafly Tundra universal wing mount: https://www.thingiverse.com/thing:4357646 GoPro mount are mounted by 2pcs M3x10 countersunk screws. ...

Motor mount to be able to put another type of engine on the durafly tundra. ... The engine mount immediately has an extra spacer for placing 3632 size brushles engines

Durafly Tundra (V2) wheel chocks for easy transport. These stop the plane from rolling around on the bench in the workshop or in the car during the trip to the field. Compared to others these minimise print material and grip the wheel and stay with...

Mount for durafly tundra bombay slot to add a camera i used some straps to mount a small hd camera. ... result: https://youtube.com/shorts/RfguNfJ4sSo?feature=share Requires 2 M4 Screws with at 15 mm ( i recommend 20mm) or 2/3 inch

Wheel Chocks for the Durafly Tundra, to keep it from rolling around in the car while driving to the field. Remixed from sebWW2 by completely redrawing his .stl in Solidworks and adding round corners & fillets to reduce the amount of fillament. And...

magnetic spinner for durafly tundra. ... spinner works with stock 12x6 prop held in place by single neodymium magnet measuring 13mm od x 6.3mm id x 3mm thick the stock lock nut is steel so this grabs it really well tested multiple flights and never let...

I use it in my Durafly Tundra V2 for my 3S 2200mAh battery. It makes it easy accessible and fixes the cog. The battery is fixed with a rubber band to the battery tray. The tray itself slides into the tray-mount, wich is glued to the airplane. The...

Battery holder for the Durafly Tundra, It has a 2200mAh Lipo battery for the engine and another 1300mAh for the FPV equipment, it has several holes to vary the center of gravity. To hold the batteries just use a rubber band, and to hold the whole set...

A battery tray designed to hold a standard 2200mah pack in the cavernous body of the Durafly Tundra. You need to print the tray, glue it together, fit a pack and then figure out where to put the tray to get the right CoG. The design is printed in...

motor mount for stock tundra includes thrust angles...its a bit thicker than the factory part but if your plane needs this im guessing its as smashed as mine and therefore the foam can now be formed with glue lol print 100 fill with support touching...

A quick remix so I can mount my Action cam into my Tundra using generic GoPro mount

For when you inevitably strip the threads on the naff aluminium one, print this and stick an m6 cap screw in the middle, and get flying! print with 5+ perimeters, 4+top and bottom layers and 40+% infill to be certain it is strong enough. if you...

The newer Tundra's are shipping with aftermarket struts for the elevators, and they are absolutely crap. So i've drawn some fittings that will hopefully do a better job of fixing it. If you did not get the crap struts, they are 3x1mm profile and...

The servo controls push rod to release a rubber band holding anything on the bottom of the Tundra. ... Needed to make it work: 1x 12g servo - I used a TowerPro MG90S 1x small zip tie to hold the servo wires in place 1x M3 screw to hold the rubber...