eachine trashcan 3d models
3846 3d models found related to eachine trashcan.thingiverse
battery holder for the Eachine Trashcan it holds 2 450mah 1s lipos.
thingiverse
Lipohalter für den Eachine Trashcan 75, damit kann man 1s oder 2s fliegen mit den standart Lipos
thingiverse
Alternative canopy for eachine trashcan drone. For Caddx Ant camera. It is attached to a frame with four screws. ... Reduces jello
thingiverse
The Eachine TRASHCAN is missing a lipo holder so they get ejected too easily. This will keep them in the battery bay. ... Get the TRASHCAN here - http://bit.ly/2StC08r
thingiverse
Micro buzzer mount for Eachine Trashcan tinywhoop designed to be mounted instead of original LED strip PCB. Printed this using standard PLA as this makes frame more stiff at the back just as when LED PCB is mounted. ... Glue it to the frame using...
thingiverse
--Designed for TPU as it relies on the flexibility to insert the batteries snuggly-- So one of the reasons why you see a lot of the reviewers experience shit flight characteristics with the eachine trashcan is that the batteries are quite loose in...
thingiverse
Couple of light functional battery retention straps for Mobula7 v1-2 & 3/Eachine Trashcan. ... Use supports, no guarantees, dug this out on request, believe these are final versions.
thingiverse
adapters for my eachine trashcan bracket. so you can use the stock 1s batteries in it as 1s or 2s. ... https://www.thingiverse.com/thing:3666971
thingiverse
Space for the trashcan, props, batteries, charger, the bag of bits it came with and a compartment spare for putting smarties or anything you want really. I didn't have separate spaces for each battery as im still undecided as to go 2S with the xt30...
thingiverse
This is a simple and lightweight adapter to use 1S 250mah/300mah on the original Eachine trashcan battery support, this locks into the space and it's handy to use and super light (less than 1g). Recommend to print in TPU. Added new version with...
thingiverse
Micro buzzer with VTX antenna mount for Eachine Trashcan tinywhoop designed to be mounted instead of original LED strip PCB. ... UPDATE: added longer version to move antenna a little closer to the canopy for better CG.
cults3d
I wanted a different support for my Eachine Trashcan drone and I ended up creating this piece. It was simple but allowed me to leave the Trashcan as a table top. Print at 0.1 to 0.2 resolution. Attention: It will only work if your Trashcan has the...
thingiverse
I wanted a different support for my Eachine Trashcan drone and I ended up creating this piece. It was simple but allowed me to leave the Trashcan as a table top. Print at 0.1 to 0.2 resolution. Attention: It will only work if your Trashcan has the...
thingiverse
This print includes two adapters for the Eachine Trashcan. The larger one will hold a 450mAh 1s in place. The smaller one will fit two 250-300mAh 1s lipos side by side or provide a lower weight for the 450mAh. ...Use 20% infill out of TPU for best...
thingiverse
This is a compact alternative to the case that comes with the Eachine Trashcan that can hold way too many batteries and spare props. There are multiple configurations that you can make alongside with the top lids being able to connect to the bottom...
thingiverse
I designed this from scratch as a direct replacement for the stock camera pod used on the Eachine Trashcan. The Trashcan is well known for vibrations in it's camera feed (jello). This aims to reduce or even eliminate this. The stock pod is very...
thingiverse
Two battery holders for the Eachine Trsahcan quadcopter. ... More details and photos to come...
thingiverse
This LiPo holder for the Trashcan clips into the frame so that it doesn't fall out while changing batteries. ...It holds two stick LiPos snugly and can also hold a single 300mAh stick LiPo when running 1S.
thingiverse
Created this for better grip on battery on trashcan frame, Designed for 2 x 250 / 300mah 1s battery Its a tight fit down between the frame, but no need for cut in the frame.
thingiverse
To fit, squeeze the two sides together to fit it between the two plastic loops on the Trashcan frame, then simply slide the TPU holder onto the vertical struts on the loop. Will fit either way round. Then just slide your battery into the mount. ...See...
thingiverse
DESIGNED FOR THE HAPPYMODEL/TRASHCAN triangular VTX. Rear VTX screw is shared with canopy mount. Camera is mounted upside down and flipped in software. Wires should exit top of camera. Designed for .3 nozzle. .15 layer height works for me,...
thingiverse
In portuguese: Este é um adaptador para usar a runcam split 3 nano no eachine trashcan. ...O vídeo de montagem pode ser visto em: https://www.youtube.com/watch?v=KqkiKQpjLFI
thingiverse
Features: - Lightweight (single 0.5mm wall) - 100% Camera protection - Bottom skirt to prevent dirt entering your electronic - Smooth design (no fancy fins that bricks aerodynamics)
thingiverse
Click in solid 2s battery holder for 450mah lipo batteries. I would suggest using tree supports and have included my settings above. feel free to experiment and comment. It's a little tough to install but it can be done with patience. Put one...
thingiverse
***Pay attention to camera mount screw length*** Was Betaflight tribute caonpy, but as awesome as the bee looks on the computer, I could not get reality to match... so just a bunch of variations. Some skit down around the flight controller,...
thingiverse
Replacement for your origianl Frame. ... M2 Spacers are necessary:...
thingiverse
Hey! Here is a fresh .STL file that could be very useful if you did the "XT-30" Upgrade on your tiny brushless whoop ! One part will hold the XT-30 and the other one will hold the two lipos so you can run it 2S. ... You should print it in TPU with...
thingiverse
Printed with TPU @ 100% infill ,12mm layer 50mm speed I really recommend it to every User of the Eachine Trashcan because the Lens is noch good protected @Stock Version. ... ( The shown Canopy is from here: https://www.thingiverse.com/thing:3374386 ...
thingiverse
STL modified for caddx Baby Ratel camera Baby Ratel from Aliexpress: https://ali.ski/4XY6-R Banggood: https://fas.st/k13TLa XT-XINTE: ...
thingiverse
needed to make a holder for my 1s 550mah batteries