ender 3 400xl 3d models
773756 3d models found related to ender 3 400xl.thingiverse
Customized version of https://www.thingiverse.com/thing:215386 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=215386
thingiverse
This is a case for the back of your ender extender 400xl to house a raspberry pi, buck converter, motherboard and a fan i can make another version for the stock ender 3 v2 if you comment below and ask for it KEEP IN MIND THE SD CARD SLOT IS COVERED...
thingiverse
This is a case for the back of your ender extender 400xl to house a raspberry pi, buck converter, motherboard and a fan i can make another version for the stock ender 3 v2 if you comment below and ask for it KEEP IN MIND THE SD CARD SLOT IS COVERED...
thingiverse
Customized version of https://www.thingiverse.com/thing:215386 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=215386
grabcad
Here is a example of the Ender Extender 400XL for the Ender 3 Pro. I do not own any rights to any products used for this model and do not want any credit for them. I've quickly put this model together using publicly available resources to make a...
thingiverse
Ender 3 Pro 400XL Extender Light Bars - designed in Blender (files included for customization) -Designed for 20mm light strips -Use M4 hardware X Gantry Light Bracket - 310mm x 20mm Top Front Crossbar Light Bracket. ...- 440mm x 20mm
thingiverse
I that design and offset the frame mount bracket a bit more so that the USB ports would not have interference with the 1010 extruded cross brace that is part of the Ender Extender 400XL kit. I also removed the tab from the rear that was for mounting...
thingiverse
Cable chain brackets designed for the Ender Extender 400XL. (May work on other versions) This setup will require you to extend your wiring. The PM_v1.3_EZR_Struder_Front_Facing_Adapter_w_Cable_Chain_Mount is designed for the Printermods.com...
cults3d
This is for the X-gantry of the Ender Extender 400/400XL Kit I just used a drill to tap the holes a little bigger and used t slot nuts I used 24v white led strips but you can use whatever obviously, I actually always super glue (the gel kind) the led...
thingiverse
This is for the X-gantry of the Ender Extender 400/400XL Kit I just used a drill to tap the holes a little bigger and used t slot nuts I used 24v white led strips but you can use whatever obviously, I actually always super glue (the gel kind) the led...
prusaprinters
Z-Brace for the ender extender 400XL, requires following hardware:M8 threadM5 bolts M5 T-NutsOptional: washers Additional tip: my Z extrusions were not entirely flat on the bottom side. I used a thin metal plate to compensate for this which...
thingiverse
this is a remix of a case design for the skr 2 by SB903 BigTreeTech SKR 2 case for Ender 3 Pro: https://www.thingiverse.com/thing:5013886 I have adapted this to fit an ender 3 that has been upgraded with an ender extender mod
thingiverse
ENDER 400XL ONLY This is an electronic enclosure designed for the ENDER 400XL build kit. The enclosure will hold the standard mainboard or similar format (BTT SKR V1.2, 2.0 etc.), a Raspberry Pi 3, DC-DC buck converters, and a 5V relay. The...
thingiverse
Designed this two-part wire strain relief for the Ender Extender 400XL and the 600-watt AC-powered silicone heater. This mounts directly on the bed just offset from the center enough to route the wires away from the motor and all. Use M3...
thingiverse
This is a quick and dirty remix of the excellent Rigid Systems Z brace for the Ender Extender 400xl. The bottom brace brackets were modified to fit the non-pro version of the Ender Extender 400xl. ...Use the original version of the top brackets!
thingiverse
Having lost the USB cap for my Lezyne 400XL bike light I decided to design a replacement to protect the charge plug on the light. This uses the same push fit as the original but if an elastic band is used around the handle bar mount it can be...
myminifactory
This is my first upgrade for Ender 3 printer from long extruder to short extruder
thingiverse
This is my first upgrade for Ender 3 printer from long extruder to short extruder
thingiverse
This is a dial mount for the digital indicator from harbor freight #63613 to help with the bed tram 1 1" 1/4 bolt and nut needed Made this for the ender 5 may also work for the ender 3
thingiverse
remixed to make it a cip in instead of t nut. ... one for the stock ender 3 pro extruder and one for the winstin dual gear metal extruder.
thingiverse
Dial Comparator support for My Ender-3 Designed for Dial comparator : Neoteck DTI Digital Dial Indicator 0.01/.0005” Digital Probe Indicator http://www.neoteck.cn/index.php/2016/11/17/ntk021/ The Gcode file included in this post is the code used to...
thingiverse
This was originally posted to the Ender 3 Facebook page. I am putting it here as i could not find it. If you are the original maker let me know and I will add you for credit. Original Descr: Here's a rough STL model of the printer mostly for...
thingiverse
I lost the USB charge cover for my Lezyne 400XL light, so made a new one. ... A little light sanding got the cover fitting really snug and looks great in white against the silver light.
thingiverse
I was asked to create a more traditional bicycle light bracket to replace the awful rubber one that is on the Lezyne Micro Drive 400xl bike light. Remove the existing rubber bracket from the Lezyne and use that existing allen key bolt to attach the...
thingiverse
A mix of a sharpie holder and an ender 3 filament guide I found on google. Used for coloring filament for some fun effects. Update. stuck with the mount design because I'm not planning on using it all the time and wanted an easy way to take...