ender 3 pro cooling duct 3d models
885007 3d models found related to ender 3 pro cooling duct.thingiverse
--------------------------------------------------------------------------------------------------------------------------- This is a cooling duct system for the Creality Ender3. The purpose was to replace the stock fan with a 40x20mm fan instead. ...
cults3d
This is a cooling duct system for the Creality Ender3. The purpose was to replace the stock fan with a 40x20mm fan instead. I wanted to get close to the print head but only put air on the part, not the nozzle.For that purpose I used the nozzle...
thingiverse
I designed this for my ender 3 pro which has an MK8 hot end. Because this hot end is a bit bigger than standard, I had to adjust the duct so that the air is better guided. Can be printed with PLA. ... I've added a .FCSt file so you can edit it...
thingiverse
277 / 5.000 Vertaalresultaten I designed this because the stock fan duct was no longer blowing air where it should with my MK8 hot end. I also designed it in such a way that the hot end fan no longer overrules the cooling part fan. ... Must be printed...
thingiverse
Remix from wheelwrench adding a guard below the part cooling fan and beefing up the top layer that touches the silicon cover. ... Printed at 200c with build plate temp of 60c with my Modded Ender 3 Pro.
thingiverse
... ...All credit should go to SignalSpirit! I made it a bit shorter and slightly angled down from inside the duct to help air flow hit the print better. ...I had an issue where the original design would blow above the print causing bridging issues.
thingiverse
It turned out perfect and fits right in after printing! ... Be carefull if you use supports when getting them off!
thingiverse
I had a problem with the ears that hold the fan on the original so I added some reinforcements
thingiverse
This is a clip on part cooling duct I designed for the Ender 3 Pro. No need to remove or replace any OEM parts, just print it and clip it on. Seeing the wide opening far away from the base of the nozzle I decided to create a duct to direct air just...
thingiverse
This is a remix of https://www.thingiverse.com/thing:3676132/files designed to slide over the stock fan bracket on the ender 3 with my Volcano hot end. ... 4x m4 screws One of the screws holding the stock cooling fan on 60mm fan
thingiverse
Remixed this to have no logo and just the tabs needed on my Ender 3 Pro purchased in December of 2019. Yours may need the second set of tabs, if so, check the originals files. No built in supports so support is needed. Use "Touching Buildplate"...
cults3d
I manually put some internal supports, but it doesn't interfere with the airflow, so you can print completely without support. In the small lock that is on the outside, I also put a support manually, just remove it with a blade. ... Attention: I...
thingiverse
Some people, like me, were having trouble printing with certain types of materials, because of the supports. I did this remix, and manually placed some internal supports, however it does not interfere with the air flow, so you can print completely...
prusaprinters
This is a remix of Roma Aquatic's Stealthburner cooling duct for the Microswiss Direct Drive (https://www.thingiverse.com/thing:5178108); I just changed the location of the mounting holes to make it suitable for the regular Ender 3 X carriage. ...I...
thingiverse
Ender 2 Pro / Ender 3 - 5015 part cooling fan duct with easy to install magnetic mount. Compatible with separate CR touch mount. Minimalist, compact and flexible design. This design has considered easy remix of your own mount for other printers. -...
thingiverse
This thing is a duct for mounting three 5015 blowers on the x-axis gantry of an Ender 3 Pro. I used six #8-32 x 1" long flat head socket cap screws and #8-32 brass nylock nuts to mount the fans to the duct and standard M4 T Slide Nuts for 20-20...
thingiverse
Made this remix in preparation of getting a second 5015 fan for my Ender 3 S1 PRO since I couldn't find any other that was suited for me. I'm a total noob at CAD or 3d editing, so I just went for the straight cut/copy/paste mode with Microsoft 3D...
thingiverse
This is a high airflow cooling duct for the Ender 3/3 PRO and CR-10 This design enables conversion from bowden tube to direct drive link to buy the 2 blower fans:...
thingiverse
For example: https://cults3d.com/en/3d-model/tool/creality-ender-3-s1-pro-cr-touch-no-y-offset https://www.printables.com/model/257460-ender-3-s1-zero-offset-cr-touch-mount This fan duct is a must if you are planning on using klipper with the...
prusaprinters
Disclaimer: Due to duct tips having close vicinity to the nozzle, use at your own risk of failed print depositing globs covering/melting the ducts.Low-profile part-cooling duct for stock Creality Sprite Sprite-Pro extruder 40x40 part cooling fan. I...
thingiverse
++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++ If you have different heater block & nozzle that compare to the stock one and you need the duct to be extend downward, leaving a comment and telling me the length you need the duct...
thingiverse
Remix of Mistral-E's Ender 3 (Pro) Cooling Duct - Removes the built in support on the right
thingiverse
Here's a Cooling Duct or the Ender 3, Also included my logo to make a dual color print if you have a color mixing printer. select part per extruder and merge both objects. The Dual color stl will print with inset letters if you print it by...
thingiverse
This is just another cooling duct for the Ender 3. It works with the standard part cooling fan and assembly oft the Ender 3. I had some problems with other cooling mods, because they were to close to the Nozzle or to close to the heater block. ... ...
thingiverse
The stock cooling duct on my Ender 3 V2 did not cool the back of the part well. I designed this to help improve that. I wanted to keep the stock parts and look. I added two flow straighteners. From my experience, the blower fan pushes all the air to...
prusaprinters
***I designed this duct for better part cooling on my Ender 3Originally designed to fit the Bullseye base design, so it is compatible with the Bullseye. The base was designed for better fitment with the Micro Swiss hot end and Direct drive...
thingiverse
... like to get some ABS for the item. I have noticed a slight deformation from the first few layers while the fan is inactive. The warping has yet to interfere with the duct's effectiveness or clearance, but a more heat resistant part would be ideal.
cults3d
This is the remit of the slim version of the "Creallity Ender 3 Cooling Fan Duct - NEW UPGRADE" I just added a back plate to disallow the airflow to go behind the hotend. Ender 3 / Pro have a bad part cooling design. ...The heatsink cooler fan just...
thingiverse
This is the remit of the slim version of the "Creallity Ender 3 Cooling Fan Duct - NEW UPGRADE" I just added a back plate to disallow the airflow to go behind the hotend. Ender 3 / Pro have a bad part cooling design. ...The heatsink cooler fan just...