ender 3 replacement power supply 3d models

Help reduce some swaying of the upright bars on an Ender 3, Pro, v2, X. Only will fit if you have relocated power supply. Slides into upright T-slots and connects to horizontal bar with 2 t-nuts. 170mm tall can be made taller for additional...

Ender 3 V2 drawer replacement for Raspberry Pi with Meanwell Power Supply Space for MEANWELL original RS-15-5 5V 3A Single Output Switching Power Supply AC-DC (I first used a DC/DC converter but it brunbed up so I decides to use an extra Power Supply...

Ender 3 Power Supply Holder .

Power supply holder for the Ender 3 / Pro, for those who the print bed touch the power supply.

Stand for Ender 3 power supply. ...Could be needed if you have electronic part externally from printer.

Power supply up higher so cable can exit next to rear electronics case for ender 3 V1

Ender 3 factory power supply cover for 80mm fan with LM2596 DC to DC buck converter 24V to 12V.

Here is the 3d model of a power supply cover for the Ender 3 to insert over the original power supply. ...designed to accommodate the exelent silencer for Maxdarkdog power supply https://www.thingiverse.com/thing:2284893 I advise the use of double...

Ender 3 Power Supply holder for glueing. ... Print in PLA or ABS Resolution: 0.2 Infill: 100% Scale: 100% Supports: No Rafts Brims: No

I made this to move the power supply over on my Ender 3 pro So the Mat didn't Fold up

This is a mod for those who want to move their power supply to be able to mount a second stepper motor for dual Z axis on their Ender 3. ..."note" you will need a 90 degree powercable and two m4*6mm will be needed to mount the power supply to the brace.

POWER SUPPLY HOLDER

I purchased a dual Z kit for my Ender 3, but I wasn't satisfied with the power supply relocation brackets included in the kit. I designed this part to slide into the 4040 extrusion and optionally be secured with an M4 screw and T-nut. You will have...

I designed this simple cover to put over an Ender 3 or Pro power supply. Easy to print and I just attached mine with some double sided tape. This has design has the cut out for the fan and the vents on the front of the unit. ... Dresses up your Ender 3...

This is a mount that holds the power supply of the Ender 3 Pro to a wall or a the side of a cabinet. It has a hole in the bottom to pass the cables through. ...I made it because I made an enclosure so I could print Abs, and since when printing with abs...

This power supply bracket/mount is meant for the Ender 3, due to my upgrade to dual Z i needed to find a new spot for the power supply. I blew myself away with this design, everything fitted (this is rare for me). This bracket allows for a nicer, and...

> # Ender 3 Power Supply Hanger > Making this for mounting the PSU of Ender 3 outside the enclosure > But can quickly mount/unmount > ## Hope this is useful! * * * > ## Hardware needed > * m4 screw ( ~25mm length ) > * for mount on the...

Stabilizing base for Ender 3 power supply. Includes support for M3x6mm screw (max. M3x8mm) for height adjustment. The stand is 18 mm higher than the original, making it stick to the printer. ... Dimensions: Height: 88.7 mm Width: 53.5 mm Wall...

The plastic cover of the power supply of my Ender 3 was falling off, so made this simple support to hold it in place. I recommend printing two so the cover is more stable. It prints in less than 15 minutes. ...Hope you like it!

this is a very easy mod to the ender 3 standard power supply (not the Meanwell power supply) the fan is a NF-A9 Noctua fan 92mm. the fan is soft mounted with the included rubber plugs. and the only part needed apart from the fan and some heat-shrink...

If you need a simple Ender 3 power supply stand because it has been separated from the frame. Supports: From the build plate only. Build plate adhesion: Doesn't matter but if you want perfect results then use a brim or raft as the stand flanges...

This is a replacement cover for the power supply unit (PSU) for the Creality Ender 3. It will directly replace the metal cover of the PSU but you will need to glue some form of thread onto the inside of the holes. I may update the model if requested...

I made this power supply cover to - give the power supply a direct support on the base frame - get more room for additional cables or other stuff

Power Support - eliminates moving plastic POWER SUPPLY X40mm Y20.51 Z9.23 If the dimensions do not match, change to those in the pictures.

This is a design of the Ender3 power supply mount. It should be strong and easily printable. I have included .step file so tha anyone can mod it as needed. Needs atleast 20-25% infill and 5 top layers to come out well. used 3 walls. ...The grooves fit...

... space for mounting power supply brackets. Important: Since the power supply is outside the printer, you must reconnect the chassis to the printer chassis with a cable !! The grounding functionality must also be verified by measurement. ...

I wanted to move my power supply to the outside of my enclosure, so I modeled this to fit around the power switch and allow the cable to pass out the bottom. ... Secures with two flathead screws.

I wanted to move my power supply to the outside of my enclosure, so I modeled this to fit around the power switch and allow the cable to pass out the bottom. ... Secures with two flathead screws.

To fix the loose cover of my power supply i created this block. The cover is only fixed by two screws but on the other side it is very loose so i blocked and fixed it. A simple support block! ...

I used this to power strip LED lights that are mounted inside the races in the frame.only the last file need support, printing switch side down, I added support the area that slides into the extrusion.This is my first remix. ... I hope it...